1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Freescale eSDHC i.MX controller driver for the platform bus.
4 *
5 * derived from the OF-version.
6 *
7 * Copyright (c) 2010 Pengutronix e.K.
8 * Author: Wolfram Sang <kernel@pengutronix.de>
9 */
10
11 #include <linux/bitfield.h>
12 #include <linux/io.h>
13 #include <linux/iopoll.h>
14 #include <linux/delay.h>
15 #include <linux/err.h>
16 #include <linux/clk.h>
17 #include <linux/module.h>
18 #include <linux/slab.h>
19 #include <linux/pm_qos.h>
20 #include <linux/mmc/host.h>
21 #include <linux/mmc/mmc.h>
22 #include <linux/mmc/sdio.h>
23 #include <linux/mmc/slot-gpio.h>
24 #include <linux/of.h>
25 #include <linux/of_device.h>
26 #include <linux/pinctrl/consumer.h>
27 #include <linux/pm_runtime.h>
28 #include "sdhci-cqhci.h"
29 #include "sdhci-pltfm.h"
30 #include "sdhci-esdhc.h"
31 #include "cqhci.h"
32
33 #define ESDHC_SYS_CTRL_DTOCV_MASK 0x0f
34 #define ESDHC_CTRL_D3CD 0x08
35 #define ESDHC_BURST_LEN_EN_INCR (1 << 27)
36 /* VENDOR SPEC register */
37 #define ESDHC_VENDOR_SPEC 0xc0
38 #define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1)
39 #define ESDHC_VENDOR_SPEC_VSELECT (1 << 1)
40 #define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8)
41 #define ESDHC_DEBUG_SEL_AND_STATUS_REG 0xc2
42 #define ESDHC_DEBUG_SEL_REG 0xc3
43 #define ESDHC_DEBUG_SEL_MASK 0xf
44 #define ESDHC_DEBUG_SEL_CMD_STATE 1
45 #define ESDHC_DEBUG_SEL_DATA_STATE 2
46 #define ESDHC_DEBUG_SEL_TRANS_STATE 3
47 #define ESDHC_DEBUG_SEL_DMA_STATE 4
48 #define ESDHC_DEBUG_SEL_ADMA_STATE 5
49 #define ESDHC_DEBUG_SEL_FIFO_STATE 6
50 #define ESDHC_DEBUG_SEL_ASYNC_FIFO_STATE 7
51 #define ESDHC_WTMK_LVL 0x44
52 #define ESDHC_WTMK_DEFAULT_VAL 0x10401040
53 #define ESDHC_WTMK_LVL_RD_WML_MASK 0x000000FF
54 #define ESDHC_WTMK_LVL_RD_WML_SHIFT 0
55 #define ESDHC_WTMK_LVL_WR_WML_MASK 0x00FF0000
56 #define ESDHC_WTMK_LVL_WR_WML_SHIFT 16
57 #define ESDHC_WTMK_LVL_WML_VAL_DEF 64
58 #define ESDHC_WTMK_LVL_WML_VAL_MAX 128
59 #define ESDHC_MIX_CTRL 0x48
60 #define ESDHC_MIX_CTRL_DDREN (1 << 3)
61 #define ESDHC_MIX_CTRL_AC23EN (1 << 7)
62 #define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22)
63 #define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23)
64 #define ESDHC_MIX_CTRL_AUTO_TUNE_EN (1 << 24)
65 #define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25)
66 #define ESDHC_MIX_CTRL_HS400_EN (1 << 26)
67 #define ESDHC_MIX_CTRL_HS400_ES_EN (1 << 27)
68 /* Bits 3 and 6 are not SDHCI standard definitions */
69 #define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
70 /* Tuning bits */
71 #define ESDHC_MIX_CTRL_TUNING_MASK 0x03c00000
72
73 /* dll control register */
74 #define ESDHC_DLL_CTRL 0x60
75 #define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9
76 #define ESDHC_DLL_OVERRIDE_EN_SHIFT 8
77
78 /* tune control register */
79 #define ESDHC_TUNE_CTRL_STATUS 0x68
80 #define ESDHC_TUNE_CTRL_STEP 1
81 #define ESDHC_TUNE_CTRL_MIN 0
82 #define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1)
83
84 /* strobe dll register */
85 #define ESDHC_STROBE_DLL_CTRL 0x70
86 #define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0)
87 #define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1)
88 #define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT 0x7
89 #define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3
90 #define ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT (4 << 20)
91
92 #define ESDHC_STROBE_DLL_STATUS 0x74
93 #define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1)
94 #define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1
95
96 #define ESDHC_VEND_SPEC2 0xc8
97 #define ESDHC_VEND_SPEC2_EN_BUSY_IRQ (1 << 8)
98 #define ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN (1 << 4)
99 #define ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN (0 << 4)
100 #define ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN (2 << 4)
101 #define ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN (1 << 6)
102 #define ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK (7 << 4)
103
104 #define ESDHC_TUNING_CTRL 0xcc
105 #define ESDHC_STD_TUNING_EN (1 << 24)
106 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
107 #define ESDHC_TUNING_START_TAP_DEFAULT 0x1
108 #define ESDHC_TUNING_START_TAP_MASK 0x7f
109 #define ESDHC_TUNING_CMD_CRC_CHECK_DISABLE (1 << 7)
110 #define ESDHC_TUNING_STEP_DEFAULT 0x1
111 #define ESDHC_TUNING_STEP_MASK 0x00070000
112 #define ESDHC_TUNING_STEP_SHIFT 16
113
114 /* pinctrl state */
115 #define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz"
116 #define ESDHC_PINCTRL_STATE_200MHZ "state_200mhz"
117
118 /*
119 * Our interpretation of the SDHCI_HOST_CONTROL register
120 */
121 #define ESDHC_CTRL_4BITBUS (0x1 << 1)
122 #define ESDHC_CTRL_8BITBUS (0x2 << 1)
123 #define ESDHC_CTRL_BUSWIDTH_MASK (0x3 << 1)
124 #define USDHC_GET_BUSWIDTH(c) (c & ESDHC_CTRL_BUSWIDTH_MASK)
125
126 /*
127 * There is an INT DMA ERR mismatch between eSDHC and STD SDHC SPEC:
128 * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
129 * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
130 * Define this macro DMA error INT for fsl eSDHC
131 */
132 #define ESDHC_INT_VENDOR_SPEC_DMA_ERR (1 << 28)
133
134 /* the address offset of CQHCI */
135 #define ESDHC_CQHCI_ADDR_OFFSET 0x100
136
137 /*
138 * The CMDTYPE of the CMD register (offset 0xE) should be set to
139 * "11" when the STOP CMD12 is issued on imx53 to abort one
140 * open ended multi-blk IO. Otherwise the TC INT wouldn't
141 * be generated.
142 * In exact block transfer, the controller doesn't complete the
143 * operations automatically as required at the end of the
144 * transfer and remains on hold if the abort command is not sent.
145 * As a result, the TC flag is not asserted and SW received timeout
146 * exception. Bit1 of Vendor Spec register is used to fix it.
147 */
148 #define ESDHC_FLAG_MULTIBLK_NO_INT BIT(1)
149 /*
150 * The flag tells that the ESDHC controller is an USDHC block that is
151 * integrated on the i.MX6 series.
152 */
153 #define ESDHC_FLAG_USDHC BIT(3)
154 /* The IP supports manual tuning process */
155 #define ESDHC_FLAG_MAN_TUNING BIT(4)
156 /* The IP supports standard tuning process */
157 #define ESDHC_FLAG_STD_TUNING BIT(5)
158 /* The IP has SDHCI_CAPABILITIES_1 register */
159 #define ESDHC_FLAG_HAVE_CAP1 BIT(6)
160 /*
161 * The IP has erratum ERR004536
162 * uSDHC: ADMA Length Mismatch Error occurs if the AHB read access is slow,
163 * when reading data from the card
164 * This flag is also set for i.MX25 and i.MX35 in order to get
165 * SDHCI_QUIRK_BROKEN_ADMA, but for different reasons (ADMA capability bits).
166 */
167 #define ESDHC_FLAG_ERR004536 BIT(7)
168 /* The IP supports HS200 mode */
169 #define ESDHC_FLAG_HS200 BIT(8)
170 /* The IP supports HS400 mode */
171 #define ESDHC_FLAG_HS400 BIT(9)
172 /*
173 * The IP has errata ERR010450
174 * uSDHC: Due to the I/O timing limit, for SDR mode, SD card clock can't
175 * exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz.
176 */
177 #define ESDHC_FLAG_ERR010450 BIT(10)
178 /* The IP supports HS400ES mode */
179 #define ESDHC_FLAG_HS400_ES BIT(11)
180 /* The IP has Host Controller Interface for Command Queuing */
181 #define ESDHC_FLAG_CQHCI BIT(12)
182 /* need request pmqos during low power */
183 #define ESDHC_FLAG_PMQOS BIT(13)
184 /* The IP state got lost in low power mode */
185 #define ESDHC_FLAG_STATE_LOST_IN_LPMODE BIT(14)
186 /* The IP lost clock rate in PM_RUNTIME */
187 #define ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME BIT(15)
188 /*
189 * The IP do not support the ACMD23 feature completely when use ADMA mode.
190 * In ADMA mode, it only use the 16 bit block count of the register 0x4
191 * (BLOCK_ATT) as the CMD23's argument for ACMD23 mode, which means it will
192 * ignore the upper 16 bit of the CMD23's argument. This will block the reliable
193 * write operation in RPMB, because RPMB reliable write need to set the bit31
194 * of the CMD23's argument.
195 * imx6qpdl/imx6sx/imx6sl/imx7d has this limitation only for ADMA mode, SDMA
196 * do not has this limitation. so when these SoC use ADMA mode, it need to
197 * disable the ACMD23 feature.
198 */
199 #define ESDHC_FLAG_BROKEN_AUTO_CMD23 BIT(16)
200
201 /* ERR004536 is not applicable for the IP */
202 #define ESDHC_FLAG_SKIP_ERR004536 BIT(17)
203
204 enum wp_types {
205 ESDHC_WP_NONE, /* no WP, neither controller nor gpio */
206 ESDHC_WP_CONTROLLER, /* mmc controller internal WP */
207 ESDHC_WP_GPIO, /* external gpio pin for WP */
208 };
209
210 enum cd_types {
211 ESDHC_CD_NONE, /* no CD, neither controller nor gpio */
212 ESDHC_CD_CONTROLLER, /* mmc controller internal CD */
213 ESDHC_CD_GPIO, /* external gpio pin for CD */
214 ESDHC_CD_PERMANENT, /* no CD, card permanently wired to host */
215 };
216
217 /*
218 * struct esdhc_platform_data - platform data for esdhc on i.MX
219 *
220 * ESDHC_WP(CD)_CONTROLLER type is not available on i.MX25/35.
221 *
222 * @wp_type: type of write_protect method (see wp_types enum above)
223 * @cd_type: type of card_detect method (see cd_types enum above)
224 */
225
226 struct esdhc_platform_data {
227 enum wp_types wp_type;
228 enum cd_types cd_type;
229 int max_bus_width;
230 unsigned int delay_line;
231 unsigned int tuning_step; /* The delay cell steps in tuning procedure */
232 unsigned int tuning_start_tap; /* The start delay cell point in tuning procedure */
233 unsigned int strobe_dll_delay_target; /* The delay cell for strobe pad (read clock) */
234 };
235
236 struct esdhc_soc_data {
237 u32 flags;
238 };
239
240 static const struct esdhc_soc_data esdhc_imx25_data = {
241 .flags = ESDHC_FLAG_ERR004536,
242 };
243
244 static const struct esdhc_soc_data esdhc_imx35_data = {
245 .flags = ESDHC_FLAG_ERR004536,
246 };
247
248 static const struct esdhc_soc_data esdhc_imx51_data = {
249 .flags = 0,
250 };
251
252 static const struct esdhc_soc_data esdhc_imx53_data = {
253 .flags = ESDHC_FLAG_MULTIBLK_NO_INT,
254 };
255
256 static const struct esdhc_soc_data usdhc_imx6q_data = {
257 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING
258 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
259 };
260
261 static const struct esdhc_soc_data usdhc_imx6sl_data = {
262 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
263 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_ERR004536
264 | ESDHC_FLAG_HS200
265 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
266 };
267
268 static const struct esdhc_soc_data usdhc_imx6sll_data = {
269 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
270 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
271 | ESDHC_FLAG_HS400
272 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
273 };
274
275 static const struct esdhc_soc_data usdhc_imx6sx_data = {
276 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
277 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
278 | ESDHC_FLAG_STATE_LOST_IN_LPMODE
279 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
280 };
281
282 static const struct esdhc_soc_data usdhc_imx6ull_data = {
283 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
284 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
285 | ESDHC_FLAG_ERR010450
286 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
287 };
288
289 static const struct esdhc_soc_data usdhc_imx7d_data = {
290 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
291 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
292 | ESDHC_FLAG_HS400
293 | ESDHC_FLAG_STATE_LOST_IN_LPMODE
294 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
295 };
296
297 static struct esdhc_soc_data usdhc_s32g2_data = {
298 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING
299 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
300 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
301 | ESDHC_FLAG_SKIP_ERR004536,
302 };
303
304 static struct esdhc_soc_data usdhc_imx7ulp_data = {
305 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
306 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
307 | ESDHC_FLAG_PMQOS | ESDHC_FLAG_HS400
308 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
309 };
310 static struct esdhc_soc_data usdhc_imxrt1050_data = {
311 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
312 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
313 };
314
315 static struct esdhc_soc_data usdhc_imx8qxp_data = {
316 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
317 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
318 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
319 | ESDHC_FLAG_STATE_LOST_IN_LPMODE
320 | ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME,
321 };
322
323 static struct esdhc_soc_data usdhc_imx8mm_data = {
324 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
325 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
326 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
327 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
328 };
329
330 struct pltfm_imx_data {
331 u32 scratchpad;
332 struct pinctrl *pinctrl;
333 struct pinctrl_state *pins_100mhz;
334 struct pinctrl_state *pins_200mhz;
335 const struct esdhc_soc_data *socdata;
336 struct esdhc_platform_data boarddata;
337 struct clk *clk_ipg;
338 struct clk *clk_ahb;
339 struct clk *clk_per;
340 unsigned int actual_clock;
341
342 /*
343 * USDHC has one limition, require the SDIO device a different
344 * register setting. Driver has to recognize card type during
345 * the card init, but at this stage, mmc_host->card is not
346 * available. So involve this field to save the card type
347 * during card init through usdhc_init_card().
348 */
349 unsigned int init_card_type;
350
351 enum {
352 NO_CMD_PENDING, /* no multiblock command pending */
353 MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */
354 WAIT_FOR_INT, /* sent CMD12, waiting for response INT */
355 } multiblock_status;
356 u32 is_ddr;
357 struct pm_qos_request pm_qos_req;
358 };
359
360 static const struct of_device_id imx_esdhc_dt_ids[] = {
361 { .compatible = "fsl,imx25-esdhc", .data = &esdhc_imx25_data, },
362 { .compatible = "fsl,imx35-esdhc", .data = &esdhc_imx35_data, },
363 { .compatible = "fsl,imx51-esdhc", .data = &esdhc_imx51_data, },
364 { .compatible = "fsl,imx53-esdhc", .data = &esdhc_imx53_data, },
365 { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
366 { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
367 { .compatible = "fsl,imx6sll-usdhc", .data = &usdhc_imx6sll_data, },
368 { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
369 { .compatible = "fsl,imx6ull-usdhc", .data = &usdhc_imx6ull_data, },
370 { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
371 { .compatible = "fsl,imx7ulp-usdhc", .data = &usdhc_imx7ulp_data, },
372 { .compatible = "fsl,imx8qxp-usdhc", .data = &usdhc_imx8qxp_data, },
373 { .compatible = "fsl,imx8mm-usdhc", .data = &usdhc_imx8mm_data, },
374 { .compatible = "fsl,imxrt1050-usdhc", .data = &usdhc_imxrt1050_data, },
375 { .compatible = "nxp,s32g2-usdhc", .data = &usdhc_s32g2_data, },
376 { /* sentinel */ }
377 };
378 MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
379
is_imx25_esdhc(struct pltfm_imx_data * data)380 static inline int is_imx25_esdhc(struct pltfm_imx_data *data)
381 {
382 return data->socdata == &esdhc_imx25_data;
383 }
384
is_imx53_esdhc(struct pltfm_imx_data * data)385 static inline int is_imx53_esdhc(struct pltfm_imx_data *data)
386 {
387 return data->socdata == &esdhc_imx53_data;
388 }
389
esdhc_is_usdhc(struct pltfm_imx_data * data)390 static inline int esdhc_is_usdhc(struct pltfm_imx_data *data)
391 {
392 return !!(data->socdata->flags & ESDHC_FLAG_USDHC);
393 }
394
esdhc_clrset_le(struct sdhci_host * host,u32 mask,u32 val,int reg)395 static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg)
396 {
397 void __iomem *base = host->ioaddr + (reg & ~0x3);
398 u32 shift = (reg & 0x3) * 8;
399
400 writel(((readl(base) & ~(mask << shift)) | (val << shift)), base);
401 }
402
403 #define DRIVER_NAME "sdhci-esdhc-imx"
404 #define ESDHC_IMX_DUMP(f, x...) \
405 pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
esdhc_dump_debug_regs(struct sdhci_host * host)406 static void esdhc_dump_debug_regs(struct sdhci_host *host)
407 {
408 int i;
409 char *debug_status[7] = {
410 "cmd debug status",
411 "data debug status",
412 "trans debug status",
413 "dma debug status",
414 "adma debug status",
415 "fifo debug status",
416 "async fifo debug status"
417 };
418
419 ESDHC_IMX_DUMP("========= ESDHC IMX DEBUG STATUS DUMP =========\n");
420 for (i = 0; i < 7; i++) {
421 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK,
422 ESDHC_DEBUG_SEL_CMD_STATE + i, ESDHC_DEBUG_SEL_REG);
423 ESDHC_IMX_DUMP("%s: 0x%04x\n", debug_status[i],
424 readw(host->ioaddr + ESDHC_DEBUG_SEL_AND_STATUS_REG));
425 }
426
427 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK, 0, ESDHC_DEBUG_SEL_REG);
428
429 }
430
esdhc_wait_for_card_clock_gate_off(struct sdhci_host * host)431 static inline void esdhc_wait_for_card_clock_gate_off(struct sdhci_host *host)
432 {
433 u32 present_state;
434 int ret;
435
436 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, present_state,
437 (present_state & ESDHC_CLOCK_GATE_OFF), 2, 100);
438 if (ret == -ETIMEDOUT)
439 dev_warn(mmc_dev(host->mmc), "%s: card clock still not gate off in 100us!.\n", __func__);
440 }
441
442 /* Enable the auto tuning circuit to check the CMD line and BUS line */
usdhc_auto_tuning_mode_sel_and_en(struct sdhci_host * host)443 static inline void usdhc_auto_tuning_mode_sel_and_en(struct sdhci_host *host)
444 {
445 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
446 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
447 u32 buswidth, auto_tune_buswidth;
448 u32 reg;
449
450 buswidth = USDHC_GET_BUSWIDTH(readl(host->ioaddr + SDHCI_HOST_CONTROL));
451
452 switch (buswidth) {
453 case ESDHC_CTRL_8BITBUS:
454 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN;
455 break;
456 case ESDHC_CTRL_4BITBUS:
457 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN;
458 break;
459 default: /* 1BITBUS */
460 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN;
461 break;
462 }
463
464 /*
465 * For USDHC, auto tuning circuit can not handle the async sdio
466 * device interrupt correctly. When sdio device use 4 data lines,
467 * async sdio interrupt will use the shared DAT[1], if enable auto
468 * tuning circuit check these 4 data lines, include the DAT[1],
469 * this circuit will detect this interrupt, take this as a data on
470 * DAT[1], and adjust the delay cell wrongly.
471 * This is the hardware design limitation, to avoid this, for sdio
472 * device, config the auto tuning circuit only check DAT[0] and CMD
473 * line.
474 */
475 if (imx_data->init_card_type == MMC_TYPE_SDIO)
476 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN;
477
478 esdhc_clrset_le(host, ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK,
479 auto_tune_buswidth | ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN,
480 ESDHC_VEND_SPEC2);
481
482 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
483 reg |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
484 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
485 }
486
esdhc_readl_le(struct sdhci_host * host,int reg)487 static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
488 {
489 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
490 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
491 u32 val = readl(host->ioaddr + reg);
492
493 if (unlikely(reg == SDHCI_PRESENT_STATE)) {
494 u32 fsl_prss = val;
495 /* save the least 20 bits */
496 val = fsl_prss & 0x000FFFFF;
497 /* move dat[0-3] bits */
498 val |= (fsl_prss & 0x0F000000) >> 4;
499 /* move cmd line bit */
500 val |= (fsl_prss & 0x00800000) << 1;
501 }
502
503 if (unlikely(reg == SDHCI_CAPABILITIES)) {
504 /* ignore bit[0-15] as it stores cap_1 register val for mx6sl */
505 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
506 val &= 0xffff0000;
507
508 /* In FSL esdhc IC module, only bit20 is used to indicate the
509 * ADMA2 capability of esdhc, but this bit is messed up on
510 * some SOCs (e.g. on MX25, MX35 this bit is set, but they
511 * don't actually support ADMA2). So set the BROKEN_ADMA
512 * quirk on MX25/35 platforms.
513 */
514
515 if (val & SDHCI_CAN_DO_ADMA1) {
516 val &= ~SDHCI_CAN_DO_ADMA1;
517 val |= SDHCI_CAN_DO_ADMA2;
518 }
519 }
520
521 if (unlikely(reg == SDHCI_CAPABILITIES_1)) {
522 if (esdhc_is_usdhc(imx_data)) {
523 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
524 val = readl(host->ioaddr + SDHCI_CAPABILITIES) & 0xFFFF;
525 else
526 /* imx6q/dl does not have cap_1 register, fake one */
527 val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
528 | SDHCI_SUPPORT_SDR50
529 | SDHCI_USE_SDR50_TUNING
530 | FIELD_PREP(SDHCI_RETUNING_MODE_MASK,
531 SDHCI_TUNING_MODE_3);
532
533 /*
534 * Do not advertise faster UHS modes if there are no
535 * pinctrl states for 100MHz/200MHz.
536 */
537 if (IS_ERR_OR_NULL(imx_data->pins_100mhz))
538 val &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50);
539 if (IS_ERR_OR_NULL(imx_data->pins_200mhz))
540 val &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_HS400);
541 }
542 }
543
544 if (unlikely(reg == SDHCI_MAX_CURRENT) && esdhc_is_usdhc(imx_data)) {
545 val = 0;
546 val |= FIELD_PREP(SDHCI_MAX_CURRENT_330_MASK, 0xFF);
547 val |= FIELD_PREP(SDHCI_MAX_CURRENT_300_MASK, 0xFF);
548 val |= FIELD_PREP(SDHCI_MAX_CURRENT_180_MASK, 0xFF);
549 }
550
551 if (unlikely(reg == SDHCI_INT_STATUS)) {
552 if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) {
553 val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
554 val |= SDHCI_INT_ADMA_ERROR;
555 }
556
557 /*
558 * mask off the interrupt we get in response to the manually
559 * sent CMD12
560 */
561 if ((imx_data->multiblock_status == WAIT_FOR_INT) &&
562 ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) {
563 val &= ~SDHCI_INT_RESPONSE;
564 writel(SDHCI_INT_RESPONSE, host->ioaddr +
565 SDHCI_INT_STATUS);
566 imx_data->multiblock_status = NO_CMD_PENDING;
567 }
568 }
569
570 return val;
571 }
572
esdhc_writel_le(struct sdhci_host * host,u32 val,int reg)573 static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
574 {
575 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
576 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
577 u32 data;
578
579 if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE ||
580 reg == SDHCI_INT_STATUS)) {
581 if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) {
582 /*
583 * Clear and then set D3CD bit to avoid missing the
584 * card interrupt. This is an eSDHC controller problem
585 * so we need to apply the following workaround: clear
586 * and set D3CD bit will make eSDHC re-sample the card
587 * interrupt. In case a card interrupt was lost,
588 * re-sample it by the following steps.
589 */
590 data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
591 data &= ~ESDHC_CTRL_D3CD;
592 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
593 data |= ESDHC_CTRL_D3CD;
594 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
595 }
596
597 if (val & SDHCI_INT_ADMA_ERROR) {
598 val &= ~SDHCI_INT_ADMA_ERROR;
599 val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR;
600 }
601 }
602
603 if (unlikely((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
604 && (reg == SDHCI_INT_STATUS)
605 && (val & SDHCI_INT_DATA_END))) {
606 u32 v;
607 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
608 v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
609 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
610
611 if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS)
612 {
613 /* send a manual CMD12 with RESPTYP=none */
614 data = MMC_STOP_TRANSMISSION << 24 |
615 SDHCI_CMD_ABORTCMD << 16;
616 writel(data, host->ioaddr + SDHCI_TRANSFER_MODE);
617 imx_data->multiblock_status = WAIT_FOR_INT;
618 }
619 }
620
621 writel(val, host->ioaddr + reg);
622 }
623
esdhc_readw_le(struct sdhci_host * host,int reg)624 static u16 esdhc_readw_le(struct sdhci_host *host, int reg)
625 {
626 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
627 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
628 u16 ret = 0;
629 u32 val;
630
631 if (unlikely(reg == SDHCI_HOST_VERSION)) {
632 reg ^= 2;
633 if (esdhc_is_usdhc(imx_data)) {
634 /*
635 * The usdhc register returns a wrong host version.
636 * Correct it here.
637 */
638 return SDHCI_SPEC_300;
639 }
640 }
641
642 if (unlikely(reg == SDHCI_HOST_CONTROL2)) {
643 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
644 if (val & ESDHC_VENDOR_SPEC_VSELECT)
645 ret |= SDHCI_CTRL_VDD_180;
646
647 if (esdhc_is_usdhc(imx_data)) {
648 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
649 val = readl(host->ioaddr + ESDHC_MIX_CTRL);
650 else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING)
651 /* the std tuning bits is in ACMD12_ERR for imx6sl */
652 val = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
653 }
654
655 if (val & ESDHC_MIX_CTRL_EXE_TUNE)
656 ret |= SDHCI_CTRL_EXEC_TUNING;
657 if (val & ESDHC_MIX_CTRL_SMPCLK_SEL)
658 ret |= SDHCI_CTRL_TUNED_CLK;
659
660 ret &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
661
662 return ret;
663 }
664
665 if (unlikely(reg == SDHCI_TRANSFER_MODE)) {
666 if (esdhc_is_usdhc(imx_data)) {
667 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
668 ret = m & ESDHC_MIX_CTRL_SDHCI_MASK;
669 /* Swap AC23 bit */
670 if (m & ESDHC_MIX_CTRL_AC23EN) {
671 ret &= ~ESDHC_MIX_CTRL_AC23EN;
672 ret |= SDHCI_TRNS_AUTO_CMD23;
673 }
674 } else {
675 ret = readw(host->ioaddr + SDHCI_TRANSFER_MODE);
676 }
677
678 return ret;
679 }
680
681 return readw(host->ioaddr + reg);
682 }
683
esdhc_writew_le(struct sdhci_host * host,u16 val,int reg)684 static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
685 {
686 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
687 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
688 u32 new_val = 0;
689
690 switch (reg) {
691 case SDHCI_CLOCK_CONTROL:
692 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
693 if (val & SDHCI_CLOCK_CARD_EN)
694 new_val |= ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
695 else
696 new_val &= ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
697 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
698 if (!(new_val & ESDHC_VENDOR_SPEC_FRC_SDCLK_ON))
699 esdhc_wait_for_card_clock_gate_off(host);
700 return;
701 case SDHCI_HOST_CONTROL2:
702 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
703 if (val & SDHCI_CTRL_VDD_180)
704 new_val |= ESDHC_VENDOR_SPEC_VSELECT;
705 else
706 new_val &= ~ESDHC_VENDOR_SPEC_VSELECT;
707 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
708 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
709 u32 v = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
710 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
711 if (val & SDHCI_CTRL_TUNED_CLK) {
712 v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
713 } else {
714 v &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
715 m &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
716 }
717
718 if (val & SDHCI_CTRL_EXEC_TUNING) {
719 v |= ESDHC_MIX_CTRL_EXE_TUNE;
720 m |= ESDHC_MIX_CTRL_FBCLK_SEL;
721 } else {
722 v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
723 }
724
725 writel(v, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
726 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
727 }
728 return;
729 case SDHCI_TRANSFER_MODE:
730 if ((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
731 && (host->cmd->opcode == SD_IO_RW_EXTENDED)
732 && (host->cmd->data->blocks > 1)
733 && (host->cmd->data->flags & MMC_DATA_READ)) {
734 u32 v;
735 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
736 v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK;
737 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
738 }
739
740 if (esdhc_is_usdhc(imx_data)) {
741 u32 wml;
742 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
743 /* Swap AC23 bit */
744 if (val & SDHCI_TRNS_AUTO_CMD23) {
745 val &= ~SDHCI_TRNS_AUTO_CMD23;
746 val |= ESDHC_MIX_CTRL_AC23EN;
747 }
748 m = val | (m & ~ESDHC_MIX_CTRL_SDHCI_MASK);
749 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
750
751 /* Set watermark levels for PIO access to maximum value
752 * (128 words) to accommodate full 512 bytes buffer.
753 * For DMA access restore the levels to default value.
754 */
755 m = readl(host->ioaddr + ESDHC_WTMK_LVL);
756 if (val & SDHCI_TRNS_DMA) {
757 wml = ESDHC_WTMK_LVL_WML_VAL_DEF;
758 } else {
759 u8 ctrl;
760 wml = ESDHC_WTMK_LVL_WML_VAL_MAX;
761
762 /*
763 * Since already disable DMA mode, so also need
764 * to clear the DMASEL. Otherwise, for standard
765 * tuning, when send tuning command, usdhc will
766 * still prefetch the ADMA script from wrong
767 * DMA address, then we will see IOMMU report
768 * some error which show lack of TLB mapping.
769 */
770 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
771 ctrl &= ~SDHCI_CTRL_DMA_MASK;
772 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
773 }
774 m &= ~(ESDHC_WTMK_LVL_RD_WML_MASK |
775 ESDHC_WTMK_LVL_WR_WML_MASK);
776 m |= (wml << ESDHC_WTMK_LVL_RD_WML_SHIFT) |
777 (wml << ESDHC_WTMK_LVL_WR_WML_SHIFT);
778 writel(m, host->ioaddr + ESDHC_WTMK_LVL);
779 } else {
780 /*
781 * Postpone this write, we must do it together with a
782 * command write that is down below.
783 */
784 imx_data->scratchpad = val;
785 }
786 return;
787 case SDHCI_COMMAND:
788 if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
789 val |= SDHCI_CMD_ABORTCMD;
790
791 if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
792 (imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
793 imx_data->multiblock_status = MULTIBLK_IN_PROCESS;
794
795 if (esdhc_is_usdhc(imx_data))
796 writel(val << 16,
797 host->ioaddr + SDHCI_TRANSFER_MODE);
798 else
799 writel(val << 16 | imx_data->scratchpad,
800 host->ioaddr + SDHCI_TRANSFER_MODE);
801 return;
802 case SDHCI_BLOCK_SIZE:
803 val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
804 break;
805 }
806 esdhc_clrset_le(host, 0xffff, val, reg);
807 }
808
esdhc_readb_le(struct sdhci_host * host,int reg)809 static u8 esdhc_readb_le(struct sdhci_host *host, int reg)
810 {
811 u8 ret;
812 u32 val;
813
814 switch (reg) {
815 case SDHCI_HOST_CONTROL:
816 val = readl(host->ioaddr + reg);
817
818 ret = val & SDHCI_CTRL_LED;
819 ret |= (val >> 5) & SDHCI_CTRL_DMA_MASK;
820 ret |= (val & ESDHC_CTRL_4BITBUS);
821 ret |= (val & ESDHC_CTRL_8BITBUS) << 3;
822 return ret;
823 }
824
825 return readb(host->ioaddr + reg);
826 }
827
esdhc_writeb_le(struct sdhci_host * host,u8 val,int reg)828 static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
829 {
830 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
831 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
832 u32 new_val = 0;
833 u32 mask;
834
835 switch (reg) {
836 case SDHCI_POWER_CONTROL:
837 /*
838 * FSL put some DMA bits here
839 * If your board has a regulator, code should be here
840 */
841 return;
842 case SDHCI_HOST_CONTROL:
843 /* FSL messed up here, so we need to manually compose it. */
844 new_val = val & SDHCI_CTRL_LED;
845 /* ensure the endianness */
846 new_val |= ESDHC_HOST_CONTROL_LE;
847 /* bits 8&9 are reserved on mx25 */
848 if (!is_imx25_esdhc(imx_data)) {
849 /* DMA mode bits are shifted */
850 new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
851 }
852
853 /*
854 * Do not touch buswidth bits here. This is done in
855 * esdhc_pltfm_bus_width.
856 * Do not touch the D3CD bit either which is used for the
857 * SDIO interrupt erratum workaround.
858 */
859 mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD);
860
861 esdhc_clrset_le(host, mask, new_val, reg);
862 return;
863 case SDHCI_SOFTWARE_RESET:
864 if (val & SDHCI_RESET_DATA)
865 new_val = readl(host->ioaddr + SDHCI_HOST_CONTROL);
866 break;
867 }
868 esdhc_clrset_le(host, 0xff, val, reg);
869
870 if (reg == SDHCI_SOFTWARE_RESET) {
871 if (val & SDHCI_RESET_ALL) {
872 /*
873 * The esdhc has a design violation to SDHC spec which
874 * tells that software reset should not affect card
875 * detection circuit. But esdhc clears its SYSCTL
876 * register bits [0..2] during the software reset. This
877 * will stop those clocks that card detection circuit
878 * relies on. To work around it, we turn the clocks on
879 * back to keep card detection circuit functional.
880 */
881 esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL);
882 /*
883 * The reset on usdhc fails to clear MIX_CTRL register.
884 * Do it manually here.
885 */
886 if (esdhc_is_usdhc(imx_data)) {
887 /*
888 * the tuning bits should be kept during reset
889 */
890 new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
891 writel(new_val & ESDHC_MIX_CTRL_TUNING_MASK,
892 host->ioaddr + ESDHC_MIX_CTRL);
893 imx_data->is_ddr = 0;
894 }
895 } else if (val & SDHCI_RESET_DATA) {
896 /*
897 * The eSDHC DAT line software reset clears at least the
898 * data transfer width on i.MX25, so make sure that the
899 * Host Control register is unaffected.
900 */
901 esdhc_clrset_le(host, 0xff, new_val,
902 SDHCI_HOST_CONTROL);
903 }
904 }
905 }
906
esdhc_pltfm_get_max_clock(struct sdhci_host * host)907 static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host)
908 {
909 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
910
911 return pltfm_host->clock;
912 }
913
esdhc_pltfm_get_min_clock(struct sdhci_host * host)914 static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host)
915 {
916 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
917
918 return pltfm_host->clock / 256 / 16;
919 }
920
esdhc_pltfm_set_clock(struct sdhci_host * host,unsigned int clock)921 static inline void esdhc_pltfm_set_clock(struct sdhci_host *host,
922 unsigned int clock)
923 {
924 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
925 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
926 unsigned int host_clock = pltfm_host->clock;
927 int ddr_pre_div = imx_data->is_ddr ? 2 : 1;
928 int pre_div = 1;
929 int div = 1;
930 int ret;
931 u32 temp, val;
932
933 if (esdhc_is_usdhc(imx_data)) {
934 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
935 writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
936 host->ioaddr + ESDHC_VENDOR_SPEC);
937 esdhc_wait_for_card_clock_gate_off(host);
938 }
939
940 if (clock == 0) {
941 host->mmc->actual_clock = 0;
942 return;
943 }
944
945 /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */
946 if (is_imx53_esdhc(imx_data)) {
947 /*
948 * According to the i.MX53 reference manual, if DLLCTRL[10] can
949 * be set, then the controller is eSDHCv3, else it is eSDHCv2.
950 */
951 val = readl(host->ioaddr + ESDHC_DLL_CTRL);
952 writel(val | BIT(10), host->ioaddr + ESDHC_DLL_CTRL);
953 temp = readl(host->ioaddr + ESDHC_DLL_CTRL);
954 writel(val, host->ioaddr + ESDHC_DLL_CTRL);
955 if (temp & BIT(10))
956 pre_div = 2;
957 }
958
959 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
960 temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
961 | ESDHC_CLOCK_MASK);
962 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
963
964 if (imx_data->socdata->flags & ESDHC_FLAG_ERR010450) {
965 unsigned int max_clock;
966
967 max_clock = imx_data->is_ddr ? 45000000 : 150000000;
968
969 clock = min(clock, max_clock);
970 }
971
972 while (host_clock / (16 * pre_div * ddr_pre_div) > clock &&
973 pre_div < 256)
974 pre_div *= 2;
975
976 while (host_clock / (div * pre_div * ddr_pre_div) > clock && div < 16)
977 div++;
978
979 host->mmc->actual_clock = host_clock / (div * pre_div * ddr_pre_div);
980 dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
981 clock, host->mmc->actual_clock);
982
983 pre_div >>= 1;
984 div--;
985
986 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
987 temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
988 | (div << ESDHC_DIVIDER_SHIFT)
989 | (pre_div << ESDHC_PREDIV_SHIFT));
990 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
991
992 /* need to wait the bit 3 of the PRSSTAT to be set, make sure card clock is stable */
993 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, temp,
994 (temp & ESDHC_CLOCK_STABLE), 2, 100);
995 if (ret == -ETIMEDOUT)
996 dev_warn(mmc_dev(host->mmc), "card clock still not stable in 100us!.\n");
997
998 if (esdhc_is_usdhc(imx_data)) {
999 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
1000 writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
1001 host->ioaddr + ESDHC_VENDOR_SPEC);
1002 }
1003
1004 }
1005
esdhc_pltfm_get_ro(struct sdhci_host * host)1006 static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host)
1007 {
1008 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1009 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1010 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1011
1012 switch (boarddata->wp_type) {
1013 case ESDHC_WP_GPIO:
1014 return mmc_gpio_get_ro(host->mmc);
1015 case ESDHC_WP_CONTROLLER:
1016 return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) &
1017 SDHCI_WRITE_PROTECT);
1018 case ESDHC_WP_NONE:
1019 break;
1020 }
1021
1022 return -ENOSYS;
1023 }
1024
esdhc_pltfm_set_bus_width(struct sdhci_host * host,int width)1025 static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width)
1026 {
1027 u32 ctrl;
1028
1029 switch (width) {
1030 case MMC_BUS_WIDTH_8:
1031 ctrl = ESDHC_CTRL_8BITBUS;
1032 break;
1033 case MMC_BUS_WIDTH_4:
1034 ctrl = ESDHC_CTRL_4BITBUS;
1035 break;
1036 default:
1037 ctrl = 0;
1038 break;
1039 }
1040
1041 esdhc_clrset_le(host, ESDHC_CTRL_BUSWIDTH_MASK, ctrl,
1042 SDHCI_HOST_CONTROL);
1043 }
1044
esdhc_reset_tuning(struct sdhci_host * host)1045 static void esdhc_reset_tuning(struct sdhci_host *host)
1046 {
1047 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1048 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1049 u32 ctrl;
1050 int ret;
1051
1052 /* Reset the tuning circuit */
1053 if (esdhc_is_usdhc(imx_data)) {
1054 ctrl = readl(host->ioaddr + ESDHC_MIX_CTRL);
1055 ctrl &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN;
1056 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1057 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1058 ctrl &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
1059 writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
1060 writel(0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1061 } else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1062 writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
1063 ctrl = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1064 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1065 ctrl &= ~ESDHC_MIX_CTRL_EXE_TUNE;
1066 writel(ctrl, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1067 /* Make sure ESDHC_MIX_CTRL_EXE_TUNE cleared */
1068 ret = readl_poll_timeout(host->ioaddr + SDHCI_AUTO_CMD_STATUS,
1069 ctrl, !(ctrl & ESDHC_MIX_CTRL_EXE_TUNE), 1, 50);
1070 if (ret == -ETIMEDOUT)
1071 dev_warn(mmc_dev(host->mmc),
1072 "Warning! clear execute tuning bit failed\n");
1073 /*
1074 * SDHCI_INT_DATA_AVAIL is W1C bit, set this bit will clear the
1075 * usdhc IP internal logic flag execute_tuning_with_clr_buf, which
1076 * will finally make sure the normal data transfer logic correct.
1077 */
1078 ctrl = readl(host->ioaddr + SDHCI_INT_STATUS);
1079 ctrl |= SDHCI_INT_DATA_AVAIL;
1080 writel(ctrl, host->ioaddr + SDHCI_INT_STATUS);
1081 }
1082 }
1083 }
1084
usdhc_init_card(struct mmc_host * mmc,struct mmc_card * card)1085 static void usdhc_init_card(struct mmc_host *mmc, struct mmc_card *card)
1086 {
1087 struct sdhci_host *host = mmc_priv(mmc);
1088 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1089 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1090
1091 imx_data->init_card_type = card->type;
1092 }
1093
usdhc_execute_tuning(struct mmc_host * mmc,u32 opcode)1094 static int usdhc_execute_tuning(struct mmc_host *mmc, u32 opcode)
1095 {
1096 struct sdhci_host *host = mmc_priv(mmc);
1097 int err;
1098
1099 /*
1100 * i.MX uSDHC internally already uses a fixed optimized timing for
1101 * DDR50, normally does not require tuning for DDR50 mode.
1102 */
1103 if (host->timing == MMC_TIMING_UHS_DDR50)
1104 return 0;
1105
1106 /*
1107 * Reset tuning circuit logic. If not, the previous tuning result
1108 * will impact current tuning, make current tuning can't set the
1109 * correct delay cell.
1110 */
1111 esdhc_reset_tuning(host);
1112 err = sdhci_execute_tuning(mmc, opcode);
1113 /* If tuning done, enable auto tuning */
1114 if (!err && !host->tuning_err)
1115 usdhc_auto_tuning_mode_sel_and_en(host);
1116
1117 return err;
1118 }
1119
esdhc_prepare_tuning(struct sdhci_host * host,u32 val)1120 static void esdhc_prepare_tuning(struct sdhci_host *host, u32 val)
1121 {
1122 u32 reg;
1123 u8 sw_rst;
1124 int ret;
1125
1126 /* FIXME: delay a bit for card to be ready for next tuning due to errors */
1127 mdelay(1);
1128
1129 /* IC suggest to reset USDHC before every tuning command */
1130 esdhc_clrset_le(host, 0xff, SDHCI_RESET_ALL, SDHCI_SOFTWARE_RESET);
1131 ret = readb_poll_timeout(host->ioaddr + SDHCI_SOFTWARE_RESET, sw_rst,
1132 !(sw_rst & SDHCI_RESET_ALL), 10, 100);
1133 if (ret == -ETIMEDOUT)
1134 dev_warn(mmc_dev(host->mmc),
1135 "warning! RESET_ALL never complete before sending tuning command\n");
1136
1137 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
1138 reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL |
1139 ESDHC_MIX_CTRL_FBCLK_SEL;
1140 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
1141 writel(val << 8, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1142 dev_dbg(mmc_dev(host->mmc),
1143 "tuning with delay 0x%x ESDHC_TUNE_CTRL_STATUS 0x%x\n",
1144 val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS));
1145 }
1146
esdhc_post_tuning(struct sdhci_host * host)1147 static void esdhc_post_tuning(struct sdhci_host *host)
1148 {
1149 u32 reg;
1150
1151 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
1152 reg &= ~ESDHC_MIX_CTRL_EXE_TUNE;
1153 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
1154 }
1155
esdhc_executing_tuning(struct sdhci_host * host,u32 opcode)1156 static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode)
1157 {
1158 int min, max, avg, ret;
1159
1160 /* find the mininum delay first which can pass tuning */
1161 min = ESDHC_TUNE_CTRL_MIN;
1162 while (min < ESDHC_TUNE_CTRL_MAX) {
1163 esdhc_prepare_tuning(host, min);
1164 if (!mmc_send_tuning(host->mmc, opcode, NULL))
1165 break;
1166 min += ESDHC_TUNE_CTRL_STEP;
1167 }
1168
1169 /* find the maxinum delay which can not pass tuning */
1170 max = min + ESDHC_TUNE_CTRL_STEP;
1171 while (max < ESDHC_TUNE_CTRL_MAX) {
1172 esdhc_prepare_tuning(host, max);
1173 if (mmc_send_tuning(host->mmc, opcode, NULL)) {
1174 max -= ESDHC_TUNE_CTRL_STEP;
1175 break;
1176 }
1177 max += ESDHC_TUNE_CTRL_STEP;
1178 }
1179
1180 /* use average delay to get the best timing */
1181 avg = (min + max) / 2;
1182 esdhc_prepare_tuning(host, avg);
1183 ret = mmc_send_tuning(host->mmc, opcode, NULL);
1184 esdhc_post_tuning(host);
1185
1186 dev_dbg(mmc_dev(host->mmc), "tuning %s at 0x%x ret %d\n",
1187 ret ? "failed" : "passed", avg, ret);
1188
1189 return ret;
1190 }
1191
esdhc_hs400_enhanced_strobe(struct mmc_host * mmc,struct mmc_ios * ios)1192 static void esdhc_hs400_enhanced_strobe(struct mmc_host *mmc, struct mmc_ios *ios)
1193 {
1194 struct sdhci_host *host = mmc_priv(mmc);
1195 u32 m;
1196
1197 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1198 if (ios->enhanced_strobe)
1199 m |= ESDHC_MIX_CTRL_HS400_ES_EN;
1200 else
1201 m &= ~ESDHC_MIX_CTRL_HS400_ES_EN;
1202 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1203 }
1204
esdhc_change_pinstate(struct sdhci_host * host,unsigned int uhs)1205 static int esdhc_change_pinstate(struct sdhci_host *host,
1206 unsigned int uhs)
1207 {
1208 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1209 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1210 struct pinctrl_state *pinctrl;
1211
1212 dev_dbg(mmc_dev(host->mmc), "change pinctrl state for uhs %d\n", uhs);
1213
1214 if (IS_ERR(imx_data->pinctrl) ||
1215 IS_ERR(imx_data->pins_100mhz) ||
1216 IS_ERR(imx_data->pins_200mhz))
1217 return -EINVAL;
1218
1219 switch (uhs) {
1220 case MMC_TIMING_UHS_SDR50:
1221 case MMC_TIMING_UHS_DDR50:
1222 pinctrl = imx_data->pins_100mhz;
1223 break;
1224 case MMC_TIMING_UHS_SDR104:
1225 case MMC_TIMING_MMC_HS200:
1226 case MMC_TIMING_MMC_HS400:
1227 pinctrl = imx_data->pins_200mhz;
1228 break;
1229 default:
1230 /* back to default state for other legacy timing */
1231 return pinctrl_select_default_state(mmc_dev(host->mmc));
1232 }
1233
1234 return pinctrl_select_state(imx_data->pinctrl, pinctrl);
1235 }
1236
1237 /*
1238 * For HS400 eMMC, there is a data_strobe line. This signal is generated
1239 * by the device and used for data output and CRC status response output
1240 * in HS400 mode. The frequency of this signal follows the frequency of
1241 * CLK generated by host. The host receives the data which is aligned to the
1242 * edge of data_strobe line. Due to the time delay between CLK line and
1243 * data_strobe line, if the delay time is larger than one clock cycle,
1244 * then CLK and data_strobe line will be misaligned, read error shows up.
1245 */
esdhc_set_strobe_dll(struct sdhci_host * host)1246 static void esdhc_set_strobe_dll(struct sdhci_host *host)
1247 {
1248 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1249 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1250 u32 strobe_delay;
1251 u32 v;
1252 int ret;
1253
1254 /* disable clock before enabling strobe dll */
1255 writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) &
1256 ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
1257 host->ioaddr + ESDHC_VENDOR_SPEC);
1258 esdhc_wait_for_card_clock_gate_off(host);
1259
1260 /* force a reset on strobe dll */
1261 writel(ESDHC_STROBE_DLL_CTRL_RESET,
1262 host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1263 /* clear the reset bit on strobe dll before any setting */
1264 writel(0, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1265
1266 /*
1267 * enable strobe dll ctrl and adjust the delay target
1268 * for the uSDHC loopback read clock
1269 */
1270 if (imx_data->boarddata.strobe_dll_delay_target)
1271 strobe_delay = imx_data->boarddata.strobe_dll_delay_target;
1272 else
1273 strobe_delay = ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT;
1274 v = ESDHC_STROBE_DLL_CTRL_ENABLE |
1275 ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT |
1276 (strobe_delay << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
1277 writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1278
1279 /* wait max 50us to get the REF/SLV lock */
1280 ret = readl_poll_timeout(host->ioaddr + ESDHC_STROBE_DLL_STATUS, v,
1281 ((v & ESDHC_STROBE_DLL_STS_REF_LOCK) && (v & ESDHC_STROBE_DLL_STS_SLV_LOCK)), 1, 50);
1282 if (ret == -ETIMEDOUT)
1283 dev_warn(mmc_dev(host->mmc),
1284 "warning! HS400 strobe DLL status REF/SLV not lock in 50us, STROBE DLL status is %x!\n", v);
1285 }
1286
esdhc_set_uhs_signaling(struct sdhci_host * host,unsigned timing)1287 static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
1288 {
1289 u32 m;
1290 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1291 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1292 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1293
1294 /* disable ddr mode and disable HS400 mode */
1295 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1296 m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
1297 imx_data->is_ddr = 0;
1298
1299 switch (timing) {
1300 case MMC_TIMING_UHS_SDR12:
1301 case MMC_TIMING_UHS_SDR25:
1302 case MMC_TIMING_UHS_SDR50:
1303 case MMC_TIMING_UHS_SDR104:
1304 case MMC_TIMING_MMC_HS:
1305 case MMC_TIMING_MMC_HS200:
1306 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1307 break;
1308 case MMC_TIMING_UHS_DDR50:
1309 case MMC_TIMING_MMC_DDR52:
1310 m |= ESDHC_MIX_CTRL_DDREN;
1311 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1312 imx_data->is_ddr = 1;
1313 if (boarddata->delay_line) {
1314 u32 v;
1315 v = boarddata->delay_line <<
1316 ESDHC_DLL_OVERRIDE_VAL_SHIFT |
1317 (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
1318 if (is_imx53_esdhc(imx_data))
1319 v <<= 1;
1320 writel(v, host->ioaddr + ESDHC_DLL_CTRL);
1321 }
1322 break;
1323 case MMC_TIMING_MMC_HS400:
1324 m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
1325 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1326 imx_data->is_ddr = 1;
1327 /* update clock after enable DDR for strobe DLL lock */
1328 host->ops->set_clock(host, host->clock);
1329 esdhc_set_strobe_dll(host);
1330 break;
1331 case MMC_TIMING_LEGACY:
1332 default:
1333 esdhc_reset_tuning(host);
1334 break;
1335 }
1336
1337 esdhc_change_pinstate(host, timing);
1338 }
1339
esdhc_reset(struct sdhci_host * host,u8 mask)1340 static void esdhc_reset(struct sdhci_host *host, u8 mask)
1341 {
1342 sdhci_and_cqhci_reset(host, mask);
1343
1344 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
1345 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
1346 }
1347
esdhc_get_max_timeout_count(struct sdhci_host * host)1348 static unsigned int esdhc_get_max_timeout_count(struct sdhci_host *host)
1349 {
1350 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1351 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1352
1353 /* Doc Erratum: the uSDHC actual maximum timeout count is 1 << 29 */
1354 return esdhc_is_usdhc(imx_data) ? 1 << 29 : 1 << 27;
1355 }
1356
esdhc_set_timeout(struct sdhci_host * host,struct mmc_command * cmd)1357 static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
1358 {
1359 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1360 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1361
1362 /* use maximum timeout counter */
1363 esdhc_clrset_le(host, ESDHC_SYS_CTRL_DTOCV_MASK,
1364 esdhc_is_usdhc(imx_data) ? 0xF : 0xE,
1365 SDHCI_TIMEOUT_CONTROL);
1366 }
1367
esdhc_cqhci_irq(struct sdhci_host * host,u32 intmask)1368 static u32 esdhc_cqhci_irq(struct sdhci_host *host, u32 intmask)
1369 {
1370 int cmd_error = 0;
1371 int data_error = 0;
1372
1373 if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
1374 return intmask;
1375
1376 cqhci_irq(host->mmc, intmask, cmd_error, data_error);
1377
1378 return 0;
1379 }
1380
1381 static struct sdhci_ops sdhci_esdhc_ops = {
1382 .read_l = esdhc_readl_le,
1383 .read_w = esdhc_readw_le,
1384 .read_b = esdhc_readb_le,
1385 .write_l = esdhc_writel_le,
1386 .write_w = esdhc_writew_le,
1387 .write_b = esdhc_writeb_le,
1388 .set_clock = esdhc_pltfm_set_clock,
1389 .get_max_clock = esdhc_pltfm_get_max_clock,
1390 .get_min_clock = esdhc_pltfm_get_min_clock,
1391 .get_max_timeout_count = esdhc_get_max_timeout_count,
1392 .get_ro = esdhc_pltfm_get_ro,
1393 .set_timeout = esdhc_set_timeout,
1394 .set_bus_width = esdhc_pltfm_set_bus_width,
1395 .set_uhs_signaling = esdhc_set_uhs_signaling,
1396 .reset = esdhc_reset,
1397 .irq = esdhc_cqhci_irq,
1398 .dump_vendor_regs = esdhc_dump_debug_regs,
1399 };
1400
1401 static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
1402 .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
1403 | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
1404 | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
1405 | SDHCI_QUIRK_BROKEN_CARD_DETECTION,
1406 .ops = &sdhci_esdhc_ops,
1407 };
1408
sdhci_esdhc_imx_hwinit(struct sdhci_host * host)1409 static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host)
1410 {
1411 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1412 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1413 struct cqhci_host *cq_host = host->mmc->cqe_private;
1414 u32 tmp;
1415
1416 if (esdhc_is_usdhc(imx_data)) {
1417 /*
1418 * The imx6q ROM code will change the default watermark
1419 * level setting to something insane. Change it back here.
1420 */
1421 writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL);
1422
1423 /*
1424 * ROM code will change the bit burst_length_enable setting
1425 * to zero if this usdhc is chosen to boot system. Change
1426 * it back here, otherwise it will impact the performance a
1427 * lot. This bit is used to enable/disable the burst length
1428 * for the external AHB2AXI bridge. It's useful especially
1429 * for INCR transfer because without burst length indicator,
1430 * the AHB2AXI bridge does not know the burst length in
1431 * advance. And without burst length indicator, AHB INCR
1432 * transfer can only be converted to singles on the AXI side.
1433 */
1434 writel(readl(host->ioaddr + SDHCI_HOST_CONTROL)
1435 | ESDHC_BURST_LEN_EN_INCR,
1436 host->ioaddr + SDHCI_HOST_CONTROL);
1437
1438 /*
1439 * erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL
1440 * TO1.1, it's harmless for MX6SL
1441 */
1442 if (!(imx_data->socdata->flags & ESDHC_FLAG_SKIP_ERR004536)) {
1443 writel(readl(host->ioaddr + 0x6c) & ~BIT(7),
1444 host->ioaddr + 0x6c);
1445 }
1446
1447 /* disable DLL_CTRL delay line settings */
1448 writel(0x0, host->ioaddr + ESDHC_DLL_CTRL);
1449
1450 /*
1451 * For the case of command with busy, if set the bit
1452 * ESDHC_VEND_SPEC2_EN_BUSY_IRQ, USDHC will generate a
1453 * transfer complete interrupt when busy is deasserted.
1454 * When CQHCI use DCMD to send a CMD need R1b respons,
1455 * CQHCI require to set ESDHC_VEND_SPEC2_EN_BUSY_IRQ,
1456 * otherwise DCMD will always meet timeout waiting for
1457 * hardware interrupt issue.
1458 */
1459 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1460 tmp = readl(host->ioaddr + ESDHC_VEND_SPEC2);
1461 tmp |= ESDHC_VEND_SPEC2_EN_BUSY_IRQ;
1462 writel(tmp, host->ioaddr + ESDHC_VEND_SPEC2);
1463
1464 host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
1465 }
1466
1467 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1468 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1469 tmp |= ESDHC_STD_TUNING_EN;
1470
1471 /*
1472 * ROM code or bootloader may config the start tap
1473 * and step, unmask them first.
1474 */
1475 tmp &= ~(ESDHC_TUNING_START_TAP_MASK | ESDHC_TUNING_STEP_MASK);
1476 if (imx_data->boarddata.tuning_start_tap)
1477 tmp |= imx_data->boarddata.tuning_start_tap;
1478 else
1479 tmp |= ESDHC_TUNING_START_TAP_DEFAULT;
1480
1481 if (imx_data->boarddata.tuning_step) {
1482 tmp |= imx_data->boarddata.tuning_step
1483 << ESDHC_TUNING_STEP_SHIFT;
1484 } else {
1485 tmp |= ESDHC_TUNING_STEP_DEFAULT
1486 << ESDHC_TUNING_STEP_SHIFT;
1487 }
1488
1489 /* Disable the CMD CRC check for tuning, if not, need to
1490 * add some delay after every tuning command, because
1491 * hardware standard tuning logic will directly go to next
1492 * step once it detect the CMD CRC error, will not wait for
1493 * the card side to finally send out the tuning data, trigger
1494 * the buffer read ready interrupt immediately. If usdhc send
1495 * the next tuning command some eMMC card will stuck, can't
1496 * response, block the tuning procedure or the first command
1497 * after the whole tuning procedure always can't get any response.
1498 */
1499 tmp |= ESDHC_TUNING_CMD_CRC_CHECK_DISABLE;
1500 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1501 } else if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1502 /*
1503 * ESDHC_STD_TUNING_EN may be configed in bootloader
1504 * or ROM code, so clear this bit here to make sure
1505 * the manual tuning can work.
1506 */
1507 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1508 tmp &= ~ESDHC_STD_TUNING_EN;
1509 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1510 }
1511
1512 /*
1513 * On i.MX8MM, we are running Dual Linux OS, with 1st Linux using SD Card
1514 * as rootfs storage, 2nd Linux using eMMC as rootfs storage. We let
1515 * the 1st linux configure power/clock for the 2nd Linux.
1516 *
1517 * When the 2nd Linux is booting into rootfs stage, we let the 1st Linux
1518 * to destroy the 2nd linux, then restart the 2nd linux, we met SDHCI dump.
1519 * After we clear the pending interrupt and halt CQCTL, issue gone.
1520 */
1521 if (cq_host) {
1522 tmp = cqhci_readl(cq_host, CQHCI_IS);
1523 cqhci_writel(cq_host, tmp, CQHCI_IS);
1524 cqhci_writel(cq_host, CQHCI_HALT, CQHCI_CTL);
1525 }
1526 }
1527 }
1528
esdhc_cqe_enable(struct mmc_host * mmc)1529 static void esdhc_cqe_enable(struct mmc_host *mmc)
1530 {
1531 struct sdhci_host *host = mmc_priv(mmc);
1532 struct cqhci_host *cq_host = mmc->cqe_private;
1533 u32 reg;
1534 u16 mode;
1535 int count = 10;
1536
1537 /*
1538 * CQE gets stuck if it sees Buffer Read Enable bit set, which can be
1539 * the case after tuning, so ensure the buffer is drained.
1540 */
1541 reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1542 while (reg & SDHCI_DATA_AVAILABLE) {
1543 sdhci_readl(host, SDHCI_BUFFER);
1544 reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1545 if (count-- == 0) {
1546 dev_warn(mmc_dev(host->mmc),
1547 "CQE may get stuck because the Buffer Read Enable bit is set\n");
1548 break;
1549 }
1550 mdelay(1);
1551 }
1552
1553 /*
1554 * Runtime resume will reset the entire host controller, which
1555 * will also clear the DMAEN/BCEN of register ESDHC_MIX_CTRL.
1556 * Here set DMAEN and BCEN when enable CMDQ.
1557 */
1558 mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
1559 if (host->flags & SDHCI_REQ_USE_DMA)
1560 mode |= SDHCI_TRNS_DMA;
1561 if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE))
1562 mode |= SDHCI_TRNS_BLK_CNT_EN;
1563 sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
1564
1565 /*
1566 * Though Runtime resume reset the entire host controller,
1567 * but do not impact the CQHCI side, need to clear the
1568 * HALT bit, avoid CQHCI stuck in the first request when
1569 * system resume back.
1570 */
1571 cqhci_writel(cq_host, 0, CQHCI_CTL);
1572 if (cqhci_readl(cq_host, CQHCI_CTL) & CQHCI_HALT)
1573 dev_err(mmc_dev(host->mmc),
1574 "failed to exit halt state when enable CQE\n");
1575
1576
1577 sdhci_cqe_enable(mmc);
1578 }
1579
esdhc_sdhci_dumpregs(struct mmc_host * mmc)1580 static void esdhc_sdhci_dumpregs(struct mmc_host *mmc)
1581 {
1582 sdhci_dumpregs(mmc_priv(mmc));
1583 }
1584
1585 static const struct cqhci_host_ops esdhc_cqhci_ops = {
1586 .enable = esdhc_cqe_enable,
1587 .disable = sdhci_cqe_disable,
1588 .dumpregs = esdhc_sdhci_dumpregs,
1589 };
1590
1591 static int
sdhci_esdhc_imx_probe_dt(struct platform_device * pdev,struct sdhci_host * host,struct pltfm_imx_data * imx_data)1592 sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
1593 struct sdhci_host *host,
1594 struct pltfm_imx_data *imx_data)
1595 {
1596 struct device_node *np = pdev->dev.of_node;
1597 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1598 int ret;
1599
1600 if (of_get_property(np, "fsl,wp-controller", NULL))
1601 boarddata->wp_type = ESDHC_WP_CONTROLLER;
1602
1603 /*
1604 * If we have this property, then activate WP check.
1605 * Retrieveing and requesting the actual WP GPIO will happen
1606 * in the call to mmc_of_parse().
1607 */
1608 if (of_property_read_bool(np, "wp-gpios"))
1609 boarddata->wp_type = ESDHC_WP_GPIO;
1610
1611 of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
1612 of_property_read_u32(np, "fsl,tuning-start-tap",
1613 &boarddata->tuning_start_tap);
1614
1615 of_property_read_u32(np, "fsl,strobe-dll-delay-target",
1616 &boarddata->strobe_dll_delay_target);
1617 if (of_find_property(np, "no-1-8-v", NULL))
1618 host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
1619
1620 if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
1621 boarddata->delay_line = 0;
1622
1623 mmc_of_parse_voltage(host->mmc, &host->ocr_mask);
1624
1625 if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pinctrl)) {
1626 imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl,
1627 ESDHC_PINCTRL_STATE_100MHZ);
1628 imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl,
1629 ESDHC_PINCTRL_STATE_200MHZ);
1630 }
1631
1632 /* call to generic mmc_of_parse to support additional capabilities */
1633 ret = mmc_of_parse(host->mmc);
1634 if (ret)
1635 return ret;
1636
1637 if (mmc_gpio_get_cd(host->mmc) >= 0)
1638 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
1639
1640 return 0;
1641 }
1642
sdhci_esdhc_imx_probe(struct platform_device * pdev)1643 static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
1644 {
1645 struct sdhci_pltfm_host *pltfm_host;
1646 struct sdhci_host *host;
1647 struct cqhci_host *cq_host;
1648 int err;
1649 struct pltfm_imx_data *imx_data;
1650
1651 host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata,
1652 sizeof(*imx_data));
1653 if (IS_ERR(host))
1654 return PTR_ERR(host);
1655
1656 pltfm_host = sdhci_priv(host);
1657
1658 imx_data = sdhci_pltfm_priv(pltfm_host);
1659
1660 imx_data->socdata = device_get_match_data(&pdev->dev);
1661
1662 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1663 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1664
1665 imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
1666 if (IS_ERR(imx_data->clk_ipg)) {
1667 err = PTR_ERR(imx_data->clk_ipg);
1668 goto free_sdhci;
1669 }
1670
1671 imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
1672 if (IS_ERR(imx_data->clk_ahb)) {
1673 err = PTR_ERR(imx_data->clk_ahb);
1674 goto free_sdhci;
1675 }
1676
1677 imx_data->clk_per = devm_clk_get(&pdev->dev, "per");
1678 if (IS_ERR(imx_data->clk_per)) {
1679 err = PTR_ERR(imx_data->clk_per);
1680 goto free_sdhci;
1681 }
1682
1683 pltfm_host->clk = imx_data->clk_per;
1684 pltfm_host->clock = clk_get_rate(pltfm_host->clk);
1685 err = clk_prepare_enable(imx_data->clk_per);
1686 if (err)
1687 goto free_sdhci;
1688 err = clk_prepare_enable(imx_data->clk_ipg);
1689 if (err)
1690 goto disable_per_clk;
1691 err = clk_prepare_enable(imx_data->clk_ahb);
1692 if (err)
1693 goto disable_ipg_clk;
1694
1695 imx_data->pinctrl = devm_pinctrl_get(&pdev->dev);
1696 if (IS_ERR(imx_data->pinctrl))
1697 dev_warn(mmc_dev(host->mmc), "could not get pinctrl\n");
1698
1699 if (esdhc_is_usdhc(imx_data)) {
1700 host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
1701 host->mmc->caps |= MMC_CAP_1_8V_DDR | MMC_CAP_3_3V_DDR;
1702
1703 /* GPIO CD can be set as a wakeup source */
1704 host->mmc->caps |= MMC_CAP_CD_WAKE;
1705
1706 if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200))
1707 host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
1708
1709 /* clear tuning bits in case ROM has set it already */
1710 writel(0x0, host->ioaddr + ESDHC_MIX_CTRL);
1711 writel(0x0, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1712 writel(0x0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1713
1714 /*
1715 * Link usdhc specific mmc_host_ops execute_tuning function,
1716 * to replace the standard one in sdhci_ops.
1717 */
1718 host->mmc_host_ops.execute_tuning = usdhc_execute_tuning;
1719
1720 /*
1721 * Link usdhc specific mmc_host_ops init card function,
1722 * to distinguish the card type.
1723 */
1724 host->mmc_host_ops.init_card = usdhc_init_card;
1725 }
1726
1727 err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
1728 if (err)
1729 goto disable_ahb_clk;
1730
1731 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
1732 sdhci_esdhc_ops.platform_execute_tuning =
1733 esdhc_executing_tuning;
1734
1735 if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
1736 host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
1737
1738 if (host->mmc->caps & MMC_CAP_8_BIT_DATA &&
1739 imx_data->socdata->flags & ESDHC_FLAG_HS400)
1740 host->mmc->caps2 |= MMC_CAP2_HS400;
1741
1742 if (imx_data->socdata->flags & ESDHC_FLAG_BROKEN_AUTO_CMD23)
1743 host->quirks2 |= SDHCI_QUIRK2_ACMD23_BROKEN;
1744
1745 if (host->mmc->caps & MMC_CAP_8_BIT_DATA &&
1746 imx_data->socdata->flags & ESDHC_FLAG_HS400_ES) {
1747 host->mmc->caps2 |= MMC_CAP2_HS400_ES;
1748 host->mmc_host_ops.hs400_enhanced_strobe =
1749 esdhc_hs400_enhanced_strobe;
1750 }
1751
1752 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1753 host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
1754 cq_host = devm_kzalloc(&pdev->dev, sizeof(*cq_host), GFP_KERNEL);
1755 if (!cq_host) {
1756 err = -ENOMEM;
1757 goto disable_ahb_clk;
1758 }
1759
1760 cq_host->mmio = host->ioaddr + ESDHC_CQHCI_ADDR_OFFSET;
1761 cq_host->ops = &esdhc_cqhci_ops;
1762
1763 err = cqhci_init(cq_host, host->mmc, false);
1764 if (err)
1765 goto disable_ahb_clk;
1766 }
1767
1768 sdhci_esdhc_imx_hwinit(host);
1769
1770 err = sdhci_add_host(host);
1771 if (err)
1772 goto disable_ahb_clk;
1773
1774 /*
1775 * Setup the wakeup capability here, let user to decide
1776 * whether need to enable this wakeup through sysfs interface.
1777 */
1778 if ((host->mmc->pm_caps & MMC_PM_KEEP_POWER) &&
1779 (host->mmc->pm_caps & MMC_PM_WAKE_SDIO_IRQ))
1780 device_set_wakeup_capable(&pdev->dev, true);
1781
1782 pm_runtime_set_active(&pdev->dev);
1783 pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
1784 pm_runtime_use_autosuspend(&pdev->dev);
1785 pm_suspend_ignore_children(&pdev->dev, 1);
1786 pm_runtime_enable(&pdev->dev);
1787
1788 return 0;
1789
1790 disable_ahb_clk:
1791 clk_disable_unprepare(imx_data->clk_ahb);
1792 disable_ipg_clk:
1793 clk_disable_unprepare(imx_data->clk_ipg);
1794 disable_per_clk:
1795 clk_disable_unprepare(imx_data->clk_per);
1796 free_sdhci:
1797 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1798 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1799 sdhci_pltfm_free(pdev);
1800 return err;
1801 }
1802
sdhci_esdhc_imx_remove(struct platform_device * pdev)1803 static int sdhci_esdhc_imx_remove(struct platform_device *pdev)
1804 {
1805 struct sdhci_host *host = platform_get_drvdata(pdev);
1806 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1807 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1808 int dead;
1809
1810 pm_runtime_get_sync(&pdev->dev);
1811 dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
1812 pm_runtime_disable(&pdev->dev);
1813 pm_runtime_put_noidle(&pdev->dev);
1814
1815 sdhci_remove_host(host, dead);
1816
1817 clk_disable_unprepare(imx_data->clk_per);
1818 clk_disable_unprepare(imx_data->clk_ipg);
1819 clk_disable_unprepare(imx_data->clk_ahb);
1820
1821 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1822 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1823
1824 sdhci_pltfm_free(pdev);
1825
1826 return 0;
1827 }
1828
1829 #ifdef CONFIG_PM_SLEEP
sdhci_esdhc_suspend(struct device * dev)1830 static int sdhci_esdhc_suspend(struct device *dev)
1831 {
1832 struct sdhci_host *host = dev_get_drvdata(dev);
1833 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1834 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1835 int ret;
1836
1837 if (host->mmc->caps2 & MMC_CAP2_CQE) {
1838 ret = cqhci_suspend(host->mmc);
1839 if (ret)
1840 return ret;
1841 }
1842
1843 if ((imx_data->socdata->flags & ESDHC_FLAG_STATE_LOST_IN_LPMODE) &&
1844 (host->tuning_mode != SDHCI_TUNING_MODE_1)) {
1845 mmc_retune_timer_stop(host->mmc);
1846 mmc_retune_needed(host->mmc);
1847 }
1848
1849 if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1850 mmc_retune_needed(host->mmc);
1851
1852 ret = sdhci_suspend_host(host);
1853 if (ret)
1854 return ret;
1855
1856 ret = pinctrl_pm_select_sleep_state(dev);
1857 if (ret)
1858 return ret;
1859
1860 ret = mmc_gpio_set_cd_wake(host->mmc, true);
1861
1862 return ret;
1863 }
1864
sdhci_esdhc_resume(struct device * dev)1865 static int sdhci_esdhc_resume(struct device *dev)
1866 {
1867 struct sdhci_host *host = dev_get_drvdata(dev);
1868 int ret;
1869
1870 ret = pinctrl_pm_select_default_state(dev);
1871 if (ret)
1872 return ret;
1873
1874 /* re-initialize hw state in case it's lost in low power mode */
1875 sdhci_esdhc_imx_hwinit(host);
1876
1877 ret = sdhci_resume_host(host);
1878 if (ret)
1879 return ret;
1880
1881 if (host->mmc->caps2 & MMC_CAP2_CQE)
1882 ret = cqhci_resume(host->mmc);
1883
1884 if (!ret)
1885 ret = mmc_gpio_set_cd_wake(host->mmc, false);
1886
1887 return ret;
1888 }
1889 #endif
1890
1891 #ifdef CONFIG_PM
sdhci_esdhc_runtime_suspend(struct device * dev)1892 static int sdhci_esdhc_runtime_suspend(struct device *dev)
1893 {
1894 struct sdhci_host *host = dev_get_drvdata(dev);
1895 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1896 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1897 int ret;
1898
1899 if (host->mmc->caps2 & MMC_CAP2_CQE) {
1900 ret = cqhci_suspend(host->mmc);
1901 if (ret)
1902 return ret;
1903 }
1904
1905 ret = sdhci_runtime_suspend_host(host);
1906 if (ret)
1907 return ret;
1908
1909 if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1910 mmc_retune_needed(host->mmc);
1911
1912 imx_data->actual_clock = host->mmc->actual_clock;
1913 esdhc_pltfm_set_clock(host, 0);
1914 clk_disable_unprepare(imx_data->clk_per);
1915 clk_disable_unprepare(imx_data->clk_ipg);
1916 clk_disable_unprepare(imx_data->clk_ahb);
1917
1918 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1919 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1920
1921 return ret;
1922 }
1923
sdhci_esdhc_runtime_resume(struct device * dev)1924 static int sdhci_esdhc_runtime_resume(struct device *dev)
1925 {
1926 struct sdhci_host *host = dev_get_drvdata(dev);
1927 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1928 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1929 int err;
1930
1931 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1932 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1933
1934 if (imx_data->socdata->flags & ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME)
1935 clk_set_rate(imx_data->clk_per, pltfm_host->clock);
1936
1937 err = clk_prepare_enable(imx_data->clk_ahb);
1938 if (err)
1939 goto remove_pm_qos_request;
1940
1941 err = clk_prepare_enable(imx_data->clk_per);
1942 if (err)
1943 goto disable_ahb_clk;
1944
1945 err = clk_prepare_enable(imx_data->clk_ipg);
1946 if (err)
1947 goto disable_per_clk;
1948
1949 esdhc_pltfm_set_clock(host, imx_data->actual_clock);
1950
1951 err = sdhci_runtime_resume_host(host, 0);
1952 if (err)
1953 goto disable_ipg_clk;
1954
1955 if (host->mmc->caps2 & MMC_CAP2_CQE)
1956 err = cqhci_resume(host->mmc);
1957
1958 return err;
1959
1960 disable_ipg_clk:
1961 clk_disable_unprepare(imx_data->clk_ipg);
1962 disable_per_clk:
1963 clk_disable_unprepare(imx_data->clk_per);
1964 disable_ahb_clk:
1965 clk_disable_unprepare(imx_data->clk_ahb);
1966 remove_pm_qos_request:
1967 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1968 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1969 return err;
1970 }
1971 #endif
1972
1973 static const struct dev_pm_ops sdhci_esdhc_pmops = {
1974 SET_SYSTEM_SLEEP_PM_OPS(sdhci_esdhc_suspend, sdhci_esdhc_resume)
1975 SET_RUNTIME_PM_OPS(sdhci_esdhc_runtime_suspend,
1976 sdhci_esdhc_runtime_resume, NULL)
1977 };
1978
1979 static struct platform_driver sdhci_esdhc_imx_driver = {
1980 .driver = {
1981 .name = "sdhci-esdhc-imx",
1982 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
1983 .of_match_table = imx_esdhc_dt_ids,
1984 .pm = &sdhci_esdhc_pmops,
1985 },
1986 .probe = sdhci_esdhc_imx_probe,
1987 .remove = sdhci_esdhc_imx_remove,
1988 };
1989
1990 module_platform_driver(sdhci_esdhc_imx_driver);
1991
1992 MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC");
1993 MODULE_AUTHOR("Wolfram Sang <kernel@pengutronix.de>");
1994 MODULE_LICENSE("GPL v2");
1995