1 // SPDX-License-Identifier: GPL-2.0-only
2 /* intel_pch_thermal.c - Intel PCH Thermal driver
3 *
4 * Copyright (c) 2015, Intel Corporation.
5 *
6 * Authors:
7 * Tushar Dave <tushar.n.dave@intel.com>
8 */
9
10 #include <linux/acpi.h>
11 #include <linux/delay.h>
12 #include <linux/module.h>
13 #include <linux/init.h>
14 #include <linux/pci.h>
15 #include <linux/pm.h>
16 #include <linux/suspend.h>
17 #include <linux/thermal.h>
18 #include <linux/types.h>
19 #include <linux/units.h>
20
21 /* Intel PCH thermal Device IDs */
22 #define PCH_THERMAL_DID_HSW_1 0x9C24 /* Haswell PCH */
23 #define PCH_THERMAL_DID_HSW_2 0x8C24 /* Haswell PCH */
24 #define PCH_THERMAL_DID_WPT 0x9CA4 /* Wildcat Point */
25 #define PCH_THERMAL_DID_SKL 0x9D31 /* Skylake PCH */
26 #define PCH_THERMAL_DID_SKL_H 0xA131 /* Skylake PCH 100 series */
27 #define PCH_THERMAL_DID_CNL 0x9Df9 /* CNL PCH */
28 #define PCH_THERMAL_DID_CNL_H 0xA379 /* CNL-H PCH */
29 #define PCH_THERMAL_DID_CNL_LP 0x02F9 /* CNL-LP PCH */
30 #define PCH_THERMAL_DID_CML_H 0X06F9 /* CML-H PCH */
31 #define PCH_THERMAL_DID_LWB 0xA1B1 /* Lewisburg PCH */
32 #define PCH_THERMAL_DID_WBG 0x8D24 /* Wellsburg PCH */
33
34 /* Wildcat Point-LP PCH Thermal registers */
35 #define WPT_TEMP 0x0000 /* Temperature */
36 #define WPT_TSC 0x04 /* Thermal Sensor Control */
37 #define WPT_TSS 0x06 /* Thermal Sensor Status */
38 #define WPT_TSEL 0x08 /* Thermal Sensor Enable and Lock */
39 #define WPT_TSREL 0x0A /* Thermal Sensor Report Enable and Lock */
40 #define WPT_TSMIC 0x0C /* Thermal Sensor SMI Control */
41 #define WPT_CTT 0x0010 /* Catastrophic Trip Point */
42 #define WPT_TSPM 0x001C /* Thermal Sensor Power Management */
43 #define WPT_TAHV 0x0014 /* Thermal Alert High Value */
44 #define WPT_TALV 0x0018 /* Thermal Alert Low Value */
45 #define WPT_TL 0x00000040 /* Throttle Value */
46 #define WPT_PHL 0x0060 /* PCH Hot Level */
47 #define WPT_PHLC 0x62 /* PHL Control */
48 #define WPT_TAS 0x80 /* Thermal Alert Status */
49 #define WPT_TSPIEN 0x82 /* PCI Interrupt Event Enables */
50 #define WPT_TSGPEN 0x84 /* General Purpose Event Enables */
51
52 /* Wildcat Point-LP PCH Thermal Register bit definitions */
53 #define WPT_TEMP_TSR 0x01ff /* Temp TS Reading */
54 #define WPT_TSC_CPDE 0x01 /* Catastrophic Power-Down Enable */
55 #define WPT_TSS_TSDSS 0x10 /* Thermal Sensor Dynamic Shutdown Status */
56 #define WPT_TSS_GPES 0x08 /* GPE status */
57 #define WPT_TSEL_ETS 0x01 /* Enable TS */
58 #define WPT_TSEL_PLDB 0x80 /* TSEL Policy Lock-Down Bit */
59 #define WPT_TL_TOL 0x000001FF /* T0 Level */
60 #define WPT_TL_T1L 0x1ff00000 /* T1 Level */
61 #define WPT_TL_TTEN 0x20000000 /* TT Enable */
62
63 /* Resolution of 1/2 degree C and an offset of -50C */
64 #define PCH_TEMP_OFFSET (-50)
65 #define GET_WPT_TEMP(x) ((x) * MILLIDEGREE_PER_DEGREE / 2 + WPT_TEMP_OFFSET)
66 #define WPT_TEMP_OFFSET (PCH_TEMP_OFFSET * MILLIDEGREE_PER_DEGREE)
67 #define GET_PCH_TEMP(x) (((x) / 2) + PCH_TEMP_OFFSET)
68
69 #define PCH_MAX_TRIPS 3 /* critical, hot, passive */
70
71 /* Amount of time for each cooling delay, 100ms by default for now */
72 static unsigned int delay_timeout = 100;
73 module_param(delay_timeout, int, 0644);
74 MODULE_PARM_DESC(delay_timeout, "amount of time delay for each iteration.");
75
76 /* Number of iterations for cooling delay, 600 counts by default for now */
77 static unsigned int delay_cnt = 600;
78 module_param(delay_cnt, int, 0644);
79 MODULE_PARM_DESC(delay_cnt, "total number of iterations for time delay.");
80
81 static char driver_name[] = "Intel PCH thermal driver";
82
83 struct pch_thermal_device {
84 void __iomem *hw_base;
85 struct pci_dev *pdev;
86 struct thermal_zone_device *tzd;
87 struct thermal_trip trips[PCH_MAX_TRIPS];
88 bool bios_enabled;
89 };
90
91 #ifdef CONFIG_ACPI
92 /*
93 * On some platforms, there is a companion ACPI device, which adds
94 * passive trip temperature using _PSV method. There is no specific
95 * passive temperature setting in MMIO interface of this PCI device.
96 */
pch_wpt_add_acpi_psv_trip(struct pch_thermal_device * ptd,int trip)97 static int pch_wpt_add_acpi_psv_trip(struct pch_thermal_device *ptd, int trip)
98 {
99 struct acpi_device *adev;
100 int temp;
101
102 adev = ACPI_COMPANION(&ptd->pdev->dev);
103 if (!adev)
104 return 0;
105
106 if (thermal_acpi_passive_trip_temp(adev, &temp) || temp <= 0)
107 return 0;
108
109 ptd->trips[trip].type = THERMAL_TRIP_PASSIVE;
110 ptd->trips[trip].temperature = temp;
111 return 1;
112 }
113 #else
pch_wpt_add_acpi_psv_trip(struct pch_thermal_device * ptd,int trip)114 static int pch_wpt_add_acpi_psv_trip(struct pch_thermal_device *ptd, int trip)
115 {
116 return 0;
117 }
118 #endif
119
pch_thermal_get_temp(struct thermal_zone_device * tzd,int * temp)120 static int pch_thermal_get_temp(struct thermal_zone_device *tzd, int *temp)
121 {
122 struct pch_thermal_device *ptd = tzd->devdata;
123
124 *temp = GET_WPT_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP));
125 return 0;
126 }
127
pch_critical(struct thermal_zone_device * tzd)128 static void pch_critical(struct thermal_zone_device *tzd)
129 {
130 dev_dbg(&tzd->device, "%s: critical temperature reached\n", tzd->type);
131 }
132
133 static struct thermal_zone_device_ops tzd_ops = {
134 .get_temp = pch_thermal_get_temp,
135 .critical = pch_critical,
136 };
137
138 enum pch_board_ids {
139 PCH_BOARD_HSW = 0,
140 PCH_BOARD_WPT,
141 PCH_BOARD_SKL,
142 PCH_BOARD_CNL,
143 PCH_BOARD_CML,
144 PCH_BOARD_LWB,
145 PCH_BOARD_WBG,
146 };
147
148 static const char *board_names[] = {
149 [PCH_BOARD_HSW] = "pch_haswell",
150 [PCH_BOARD_WPT] = "pch_wildcat_point",
151 [PCH_BOARD_SKL] = "pch_skylake",
152 [PCH_BOARD_CNL] = "pch_cannonlake",
153 [PCH_BOARD_CML] = "pch_cometlake",
154 [PCH_BOARD_LWB] = "pch_lewisburg",
155 [PCH_BOARD_WBG] = "pch_wellsburg",
156 };
157
intel_pch_thermal_probe(struct pci_dev * pdev,const struct pci_device_id * id)158 static int intel_pch_thermal_probe(struct pci_dev *pdev,
159 const struct pci_device_id *id)
160 {
161 enum pch_board_ids board_id = id->driver_data;
162 struct pch_thermal_device *ptd;
163 int nr_trips = 0;
164 u16 trip_temp;
165 u8 tsel;
166 int err;
167
168 ptd = devm_kzalloc(&pdev->dev, sizeof(*ptd), GFP_KERNEL);
169 if (!ptd)
170 return -ENOMEM;
171
172 pci_set_drvdata(pdev, ptd);
173 ptd->pdev = pdev;
174
175 err = pci_enable_device(pdev);
176 if (err) {
177 dev_err(&pdev->dev, "failed to enable pci device\n");
178 return err;
179 }
180
181 err = pci_request_regions(pdev, driver_name);
182 if (err) {
183 dev_err(&pdev->dev, "failed to request pci region\n");
184 goto error_disable;
185 }
186
187 ptd->hw_base = pci_ioremap_bar(pdev, 0);
188 if (!ptd->hw_base) {
189 err = -ENOMEM;
190 dev_err(&pdev->dev, "failed to map mem base\n");
191 goto error_release;
192 }
193
194 /* Check if BIOS has already enabled thermal sensor */
195 if (WPT_TSEL_ETS & readb(ptd->hw_base + WPT_TSEL)) {
196 ptd->bios_enabled = true;
197 goto read_trips;
198 }
199
200 tsel = readb(ptd->hw_base + WPT_TSEL);
201 /*
202 * When TSEL's Policy Lock-Down bit is 1, TSEL become RO.
203 * If so, thermal sensor cannot enable. Bail out.
204 */
205 if (tsel & WPT_TSEL_PLDB) {
206 dev_err(&ptd->pdev->dev, "Sensor can't be enabled\n");
207 err = -ENODEV;
208 goto error_cleanup;
209 }
210
211 writeb(tsel|WPT_TSEL_ETS, ptd->hw_base + WPT_TSEL);
212 if (!(WPT_TSEL_ETS & readb(ptd->hw_base + WPT_TSEL))) {
213 dev_err(&ptd->pdev->dev, "Sensor can't be enabled\n");
214 err = -ENODEV;
215 goto error_cleanup;
216 }
217
218 read_trips:
219 trip_temp = readw(ptd->hw_base + WPT_CTT);
220 trip_temp &= 0x1FF;
221 if (trip_temp) {
222 ptd->trips[nr_trips].temperature = GET_WPT_TEMP(trip_temp);
223 ptd->trips[nr_trips++].type = THERMAL_TRIP_CRITICAL;
224 }
225
226 trip_temp = readw(ptd->hw_base + WPT_PHL);
227 trip_temp &= 0x1FF;
228 if (trip_temp) {
229 ptd->trips[nr_trips].temperature = GET_WPT_TEMP(trip_temp);
230 ptd->trips[nr_trips++].type = THERMAL_TRIP_HOT;
231 }
232
233 nr_trips += pch_wpt_add_acpi_psv_trip(ptd, nr_trips);
234
235 ptd->tzd = thermal_zone_device_register_with_trips(board_names[board_id],
236 ptd->trips, nr_trips,
237 0, ptd, &tzd_ops,
238 NULL, 0, 0);
239 if (IS_ERR(ptd->tzd)) {
240 dev_err(&pdev->dev, "Failed to register thermal zone %s\n",
241 board_names[board_id]);
242 err = PTR_ERR(ptd->tzd);
243 goto error_cleanup;
244 }
245 err = thermal_zone_device_enable(ptd->tzd);
246 if (err)
247 goto err_unregister;
248
249 return 0;
250
251 err_unregister:
252 thermal_zone_device_unregister(ptd->tzd);
253 error_cleanup:
254 iounmap(ptd->hw_base);
255 error_release:
256 pci_release_regions(pdev);
257 error_disable:
258 pci_disable_device(pdev);
259 dev_err(&pdev->dev, "pci device failed to probe\n");
260 return err;
261 }
262
intel_pch_thermal_remove(struct pci_dev * pdev)263 static void intel_pch_thermal_remove(struct pci_dev *pdev)
264 {
265 struct pch_thermal_device *ptd = pci_get_drvdata(pdev);
266
267 thermal_zone_device_unregister(ptd->tzd);
268 iounmap(ptd->hw_base);
269 pci_set_drvdata(pdev, NULL);
270 pci_release_regions(pdev);
271 pci_disable_device(pdev);
272 }
273
intel_pch_thermal_suspend_noirq(struct device * device)274 static int intel_pch_thermal_suspend_noirq(struct device *device)
275 {
276 struct pch_thermal_device *ptd = dev_get_drvdata(device);
277 u16 pch_thr_temp, pch_cur_temp;
278 int pch_delay_cnt = 0;
279 u8 tsel;
280
281 /* Shutdown the thermal sensor if it is not enabled by BIOS */
282 if (!ptd->bios_enabled) {
283 tsel = readb(ptd->hw_base + WPT_TSEL);
284 writeb(tsel & 0xFE, ptd->hw_base + WPT_TSEL);
285 return 0;
286 }
287
288 /* Do not check temperature if it is not s2idle */
289 if (pm_suspend_via_firmware())
290 return 0;
291
292 /* Get the PCH temperature threshold value */
293 pch_thr_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TSPM));
294
295 /* Get the PCH current temperature value */
296 pch_cur_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP));
297
298 /*
299 * If current PCH temperature is higher than configured PCH threshold
300 * value, run some delay loop with sleep to let the current temperature
301 * go down below the threshold value which helps to allow system enter
302 * lower power S0ix suspend state. Even after delay loop if PCH current
303 * temperature stays above threshold, notify the warning message
304 * which helps to indentify the reason why S0ix entry was rejected.
305 */
306 while (pch_delay_cnt < delay_cnt) {
307 if (pch_cur_temp < pch_thr_temp)
308 break;
309
310 if (pm_wakeup_pending()) {
311 dev_warn(&ptd->pdev->dev, "Wakeup event detected, abort cooling\n");
312 return 0;
313 }
314
315 pch_delay_cnt++;
316 dev_dbg(&ptd->pdev->dev,
317 "CPU-PCH current temp [%dC] higher than the threshold temp [%dC], sleep %d times for %d ms duration\n",
318 pch_cur_temp, pch_thr_temp, pch_delay_cnt, delay_timeout);
319 msleep(delay_timeout);
320 /* Read the PCH current temperature for next cycle. */
321 pch_cur_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP));
322 }
323
324 if (pch_cur_temp >= pch_thr_temp)
325 dev_warn(&ptd->pdev->dev,
326 "CPU-PCH is hot [%dC] after %d ms delay. S0ix might fail\n",
327 pch_cur_temp, pch_delay_cnt * delay_timeout);
328 else {
329 if (pch_delay_cnt)
330 dev_info(&ptd->pdev->dev,
331 "CPU-PCH is cool [%dC] after %d ms delay\n",
332 pch_cur_temp, pch_delay_cnt * delay_timeout);
333 else
334 dev_info(&ptd->pdev->dev,
335 "CPU-PCH is cool [%dC]\n",
336 pch_cur_temp);
337 }
338
339 return 0;
340 }
341
intel_pch_thermal_resume(struct device * device)342 static int intel_pch_thermal_resume(struct device *device)
343 {
344 struct pch_thermal_device *ptd = dev_get_drvdata(device);
345 u8 tsel;
346
347 if (ptd->bios_enabled)
348 return 0;
349
350 tsel = readb(ptd->hw_base + WPT_TSEL);
351
352 writeb(tsel | WPT_TSEL_ETS, ptd->hw_base + WPT_TSEL);
353
354 return 0;
355 }
356
357 static const struct pci_device_id intel_pch_thermal_id[] = {
358 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_HSW_1),
359 .driver_data = PCH_BOARD_HSW, },
360 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_HSW_2),
361 .driver_data = PCH_BOARD_HSW, },
362 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_WPT),
363 .driver_data = PCH_BOARD_WPT, },
364 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_SKL),
365 .driver_data = PCH_BOARD_SKL, },
366 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_SKL_H),
367 .driver_data = PCH_BOARD_SKL, },
368 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CNL),
369 .driver_data = PCH_BOARD_CNL, },
370 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CNL_H),
371 .driver_data = PCH_BOARD_CNL, },
372 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CNL_LP),
373 .driver_data = PCH_BOARD_CNL, },
374 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CML_H),
375 .driver_data = PCH_BOARD_CML, },
376 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_LWB),
377 .driver_data = PCH_BOARD_LWB, },
378 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_WBG),
379 .driver_data = PCH_BOARD_WBG, },
380 { 0, },
381 };
382 MODULE_DEVICE_TABLE(pci, intel_pch_thermal_id);
383
384 static const struct dev_pm_ops intel_pch_pm_ops = {
385 .suspend_noirq = intel_pch_thermal_suspend_noirq,
386 .resume = intel_pch_thermal_resume,
387 };
388
389 static struct pci_driver intel_pch_thermal_driver = {
390 .name = "intel_pch_thermal",
391 .id_table = intel_pch_thermal_id,
392 .probe = intel_pch_thermal_probe,
393 .remove = intel_pch_thermal_remove,
394 .driver.pm = &intel_pch_pm_ops,
395 };
396
397 module_pci_driver(intel_pch_thermal_driver);
398
399 MODULE_LICENSE("GPL v2");
400 MODULE_DESCRIPTION("Intel PCH Thermal driver");
401