1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * tas5720.c - ALSA SoC Texas Instruments TAS5720 Mono Audio Amplifier
4 *
5 * Copyright (C)2015-2016 Texas Instruments Incorporated - https://www.ti.com
6 *
7 * Author: Andreas Dannenberg <dannenberg@ti.com>
8 */
9
10 #include <linux/module.h>
11 #include <linux/errno.h>
12 #include <linux/device.h>
13 #include <linux/i2c.h>
14 #include <linux/pm_runtime.h>
15 #include <linux/regmap.h>
16 #include <linux/slab.h>
17 #include <linux/regulator/consumer.h>
18 #include <linux/delay.h>
19
20 #include <sound/pcm.h>
21 #include <sound/pcm_params.h>
22 #include <sound/soc.h>
23 #include <sound/soc-dapm.h>
24 #include <sound/tlv.h>
25
26 #include "tas5720.h"
27
28 /* Define how often to check (and clear) the fault status register (in ms) */
29 #define TAS5720_FAULT_CHECK_INTERVAL 200
30
31 enum tas572x_type {
32 TAS5720,
33 TAS5720A_Q1,
34 TAS5722,
35 };
36
37 static const char * const tas5720_supply_names[] = {
38 "dvdd", /* Digital power supply. Connect to 3.3-V supply. */
39 "pvdd", /* Class-D amp and analog power supply (connected). */
40 };
41
42 #define TAS5720_NUM_SUPPLIES ARRAY_SIZE(tas5720_supply_names)
43
44 struct tas5720_data {
45 struct snd_soc_component *component;
46 struct regmap *regmap;
47 struct i2c_client *tas5720_client;
48 enum tas572x_type devtype;
49 struct regulator_bulk_data supplies[TAS5720_NUM_SUPPLIES];
50 struct delayed_work fault_check_work;
51 unsigned int last_fault;
52 };
53
tas5720_hw_params(struct snd_pcm_substream * substream,struct snd_pcm_hw_params * params,struct snd_soc_dai * dai)54 static int tas5720_hw_params(struct snd_pcm_substream *substream,
55 struct snd_pcm_hw_params *params,
56 struct snd_soc_dai *dai)
57 {
58 struct snd_soc_component *component = dai->component;
59 unsigned int rate = params_rate(params);
60 bool ssz_ds;
61 int ret;
62
63 switch (rate) {
64 case 44100:
65 case 48000:
66 ssz_ds = false;
67 break;
68 case 88200:
69 case 96000:
70 ssz_ds = true;
71 break;
72 default:
73 dev_err(component->dev, "unsupported sample rate: %u\n", rate);
74 return -EINVAL;
75 }
76
77 ret = snd_soc_component_update_bits(component, TAS5720_DIGITAL_CTRL1_REG,
78 TAS5720_SSZ_DS, ssz_ds);
79 if (ret < 0) {
80 dev_err(component->dev, "error setting sample rate: %d\n", ret);
81 return ret;
82 }
83
84 return 0;
85 }
86
tas5720_set_dai_fmt(struct snd_soc_dai * dai,unsigned int fmt)87 static int tas5720_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt)
88 {
89 struct snd_soc_component *component = dai->component;
90 u8 serial_format;
91 int ret;
92
93 if ((fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) != SND_SOC_DAIFMT_CBC_CFC) {
94 dev_vdbg(component->dev, "DAI clocking invalid\n");
95 return -EINVAL;
96 }
97
98 switch (fmt & (SND_SOC_DAIFMT_FORMAT_MASK |
99 SND_SOC_DAIFMT_INV_MASK)) {
100 case (SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF):
101 /* 1st data bit occur one BCLK cycle after the frame sync */
102 serial_format = TAS5720_SAIF_I2S;
103 break;
104 case (SND_SOC_DAIFMT_DSP_A | SND_SOC_DAIFMT_NB_NF):
105 /*
106 * Note that although the TAS5720 does not have a dedicated DSP
107 * mode it doesn't care about the LRCLK duty cycle during TDM
108 * operation. Therefore we can use the device's I2S mode with
109 * its delaying of the 1st data bit to receive DSP_A formatted
110 * data. See device datasheet for additional details.
111 */
112 serial_format = TAS5720_SAIF_I2S;
113 break;
114 case (SND_SOC_DAIFMT_DSP_B | SND_SOC_DAIFMT_NB_NF):
115 /*
116 * Similar to DSP_A, we can use the fact that the TAS5720 does
117 * not care about the LRCLK duty cycle during TDM to receive
118 * DSP_B formatted data in LEFTJ mode (no delaying of the 1st
119 * data bit).
120 */
121 serial_format = TAS5720_SAIF_LEFTJ;
122 break;
123 case (SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_NB_NF):
124 /* No delay after the frame sync */
125 serial_format = TAS5720_SAIF_LEFTJ;
126 break;
127 default:
128 dev_vdbg(component->dev, "DAI Format is not found\n");
129 return -EINVAL;
130 }
131
132 ret = snd_soc_component_update_bits(component, TAS5720_DIGITAL_CTRL1_REG,
133 TAS5720_SAIF_FORMAT_MASK,
134 serial_format);
135 if (ret < 0) {
136 dev_err(component->dev, "error setting SAIF format: %d\n", ret);
137 return ret;
138 }
139
140 return 0;
141 }
142
tas5720_set_dai_tdm_slot(struct snd_soc_dai * dai,unsigned int tx_mask,unsigned int rx_mask,int slots,int slot_width)143 static int tas5720_set_dai_tdm_slot(struct snd_soc_dai *dai,
144 unsigned int tx_mask, unsigned int rx_mask,
145 int slots, int slot_width)
146 {
147 struct snd_soc_component *component = dai->component;
148 struct tas5720_data *tas5720 = snd_soc_component_get_drvdata(component);
149 unsigned int first_slot;
150 int ret;
151
152 if (!tx_mask) {
153 dev_err(component->dev, "tx masks must not be 0\n");
154 return -EINVAL;
155 }
156
157 /*
158 * Determine the first slot that is being requested. We will only
159 * use the first slot that is found since the TAS5720 is a mono
160 * amplifier.
161 */
162 first_slot = __ffs(tx_mask);
163
164 if (first_slot > 7) {
165 dev_err(component->dev, "slot selection out of bounds (%u)\n",
166 first_slot);
167 return -EINVAL;
168 }
169
170 /*
171 * Enable manual TDM slot selection (instead of I2C ID based).
172 * This is not applicable to TAS5720A-Q1.
173 */
174 switch (tas5720->devtype) {
175 case TAS5720A_Q1:
176 break;
177 default:
178 ret = snd_soc_component_update_bits(component, TAS5720_DIGITAL_CTRL1_REG,
179 TAS5720_TDM_CFG_SRC, TAS5720_TDM_CFG_SRC);
180 if (ret < 0)
181 goto error_snd_soc_component_update_bits;
182
183 /* Configure the TDM slot to process audio from */
184 ret = snd_soc_component_update_bits(component, TAS5720_DIGITAL_CTRL2_REG,
185 TAS5720_TDM_SLOT_SEL_MASK, first_slot);
186 if (ret < 0)
187 goto error_snd_soc_component_update_bits;
188 break;
189 }
190
191 /* Configure TDM slot width. This is only applicable to TAS5722. */
192 switch (tas5720->devtype) {
193 case TAS5722:
194 ret = snd_soc_component_update_bits(component, TAS5722_DIGITAL_CTRL2_REG,
195 TAS5722_TDM_SLOT_16B,
196 slot_width == 16 ?
197 TAS5722_TDM_SLOT_16B : 0);
198 if (ret < 0)
199 goto error_snd_soc_component_update_bits;
200 break;
201 default:
202 break;
203 }
204
205 return 0;
206
207 error_snd_soc_component_update_bits:
208 dev_err(component->dev, "error configuring TDM mode: %d\n", ret);
209 return ret;
210 }
211
tas5720_mute_soc_component(struct snd_soc_component * component,int mute)212 static int tas5720_mute_soc_component(struct snd_soc_component *component, int mute)
213 {
214 struct tas5720_data *tas5720 = snd_soc_component_get_drvdata(component);
215 unsigned int reg, mask;
216 int ret;
217
218 switch (tas5720->devtype) {
219 case TAS5720A_Q1:
220 reg = TAS5720_Q1_VOLUME_CTRL_CFG_REG;
221 mask = TAS5720_Q1_MUTE;
222 break;
223 default:
224 reg = TAS5720_DIGITAL_CTRL2_REG;
225 mask = TAS5720_MUTE;
226 break;
227 }
228
229 ret = snd_soc_component_update_bits(component, reg, mask, mute ? mask : 0);
230 if (ret < 0) {
231 dev_err(component->dev, "error (un-)muting device: %d\n", ret);
232 return ret;
233 }
234
235 return 0;
236 }
237
tas5720_mute(struct snd_soc_dai * dai,int mute,int direction)238 static int tas5720_mute(struct snd_soc_dai *dai, int mute, int direction)
239 {
240 return tas5720_mute_soc_component(dai->component, mute);
241 }
242
tas5720_fault_check_work(struct work_struct * work)243 static void tas5720_fault_check_work(struct work_struct *work)
244 {
245 struct tas5720_data *tas5720 = container_of(work, struct tas5720_data,
246 fault_check_work.work);
247 struct device *dev = tas5720->component->dev;
248 unsigned int curr_fault;
249 int ret;
250
251 ret = regmap_read(tas5720->regmap, TAS5720_FAULT_REG, &curr_fault);
252 if (ret < 0) {
253 dev_err(dev, "failed to read FAULT register: %d\n", ret);
254 goto out;
255 }
256
257 /* Check/handle all errors except SAIF clock errors */
258 curr_fault &= TAS5720_OCE | TAS5720_DCE | TAS5720_OTE;
259
260 /*
261 * Only flag errors once for a given occurrence. This is needed as
262 * the TAS5720 will take time clearing the fault condition internally
263 * during which we don't want to bombard the system with the same
264 * error message over and over.
265 */
266 if ((curr_fault & TAS5720_OCE) && !(tas5720->last_fault & TAS5720_OCE))
267 dev_crit(dev, "experienced an over current hardware fault\n");
268
269 if ((curr_fault & TAS5720_DCE) && !(tas5720->last_fault & TAS5720_DCE))
270 dev_crit(dev, "experienced a DC detection fault\n");
271
272 if ((curr_fault & TAS5720_OTE) && !(tas5720->last_fault & TAS5720_OTE))
273 dev_crit(dev, "experienced an over temperature fault\n");
274
275 /* Store current fault value so we can detect any changes next time */
276 tas5720->last_fault = curr_fault;
277
278 if (!curr_fault)
279 goto out;
280
281 /*
282 * Periodically toggle SDZ (shutdown bit) H->L->H to clear any latching
283 * faults as long as a fault condition persists. Always going through
284 * the full sequence no matter the first return value to minimizes
285 * chances for the device to end up in shutdown mode.
286 */
287 ret = regmap_write_bits(tas5720->regmap, TAS5720_POWER_CTRL_REG,
288 TAS5720_SDZ, 0);
289 if (ret < 0)
290 dev_err(dev, "failed to write POWER_CTRL register: %d\n", ret);
291
292 ret = regmap_write_bits(tas5720->regmap, TAS5720_POWER_CTRL_REG,
293 TAS5720_SDZ, TAS5720_SDZ);
294 if (ret < 0)
295 dev_err(dev, "failed to write POWER_CTRL register: %d\n", ret);
296
297 out:
298 /* Schedule the next fault check at the specified interval */
299 schedule_delayed_work(&tas5720->fault_check_work,
300 msecs_to_jiffies(TAS5720_FAULT_CHECK_INTERVAL));
301 }
302
tas5720_codec_probe(struct snd_soc_component * component)303 static int tas5720_codec_probe(struct snd_soc_component *component)
304 {
305 struct tas5720_data *tas5720 = snd_soc_component_get_drvdata(component);
306 unsigned int device_id, expected_device_id;
307 int ret;
308
309 tas5720->component = component;
310
311 ret = regulator_bulk_enable(ARRAY_SIZE(tas5720->supplies),
312 tas5720->supplies);
313 if (ret != 0) {
314 dev_err(component->dev, "failed to enable supplies: %d\n", ret);
315 return ret;
316 }
317
318 /*
319 * Take a liberal approach to checking the device ID to allow the
320 * driver to be used even if the device ID does not match, however
321 * issue a warning if there is a mismatch.
322 */
323 ret = regmap_read(tas5720->regmap, TAS5720_DEVICE_ID_REG, &device_id);
324 if (ret < 0) {
325 dev_err(component->dev, "failed to read device ID register: %d\n",
326 ret);
327 goto probe_fail;
328 }
329
330 switch (tas5720->devtype) {
331 case TAS5720:
332 expected_device_id = TAS5720_DEVICE_ID;
333 break;
334 case TAS5720A_Q1:
335 expected_device_id = TAS5720A_Q1_DEVICE_ID;
336 break;
337 case TAS5722:
338 expected_device_id = TAS5722_DEVICE_ID;
339 break;
340 default:
341 dev_err(component->dev, "unexpected private driver data\n");
342 return -EINVAL;
343 }
344
345 if (device_id != expected_device_id)
346 dev_warn(component->dev, "wrong device ID. expected: %u read: %u\n",
347 expected_device_id, device_id);
348
349 /* Set device to mute */
350 ret = tas5720_mute_soc_component(component, 1);
351 if (ret < 0)
352 goto error_snd_soc_component_update_bits;
353
354 /* Set Bit 7 in TAS5720_ANALOG_CTRL_REG to 1 for TAS5720A_Q1 */
355 switch (tas5720->devtype) {
356 case TAS5720A_Q1:
357 ret = snd_soc_component_update_bits(component, TAS5720_ANALOG_CTRL_REG,
358 TAS5720_Q1_RESERVED7_BIT,
359 TAS5720_Q1_RESERVED7_BIT);
360 break;
361 default:
362 break;
363 }
364 if (ret < 0)
365 goto error_snd_soc_component_update_bits;
366
367 /*
368 * Enter shutdown mode - our default when not playing audio - to
369 * minimize current consumption. On the TAS5720 there is no real down
370 * side doing so as all device registers are preserved and the wakeup
371 * of the codec is rather quick which we do using a dapm widget.
372 */
373 ret = snd_soc_component_update_bits(component, TAS5720_POWER_CTRL_REG,
374 TAS5720_SDZ, 0);
375 if (ret < 0)
376 goto error_snd_soc_component_update_bits;
377
378 INIT_DELAYED_WORK(&tas5720->fault_check_work, tas5720_fault_check_work);
379
380 return 0;
381
382 error_snd_soc_component_update_bits:
383 dev_err(component->dev, "error configuring device registers: %d\n", ret);
384
385 probe_fail:
386 regulator_bulk_disable(ARRAY_SIZE(tas5720->supplies),
387 tas5720->supplies);
388 return ret;
389 }
390
tas5720_codec_remove(struct snd_soc_component * component)391 static void tas5720_codec_remove(struct snd_soc_component *component)
392 {
393 struct tas5720_data *tas5720 = snd_soc_component_get_drvdata(component);
394 int ret;
395
396 cancel_delayed_work_sync(&tas5720->fault_check_work);
397
398 ret = regulator_bulk_disable(ARRAY_SIZE(tas5720->supplies),
399 tas5720->supplies);
400 if (ret < 0)
401 dev_err(component->dev, "failed to disable supplies: %d\n", ret);
402 };
403
tas5720_dac_event(struct snd_soc_dapm_widget * w,struct snd_kcontrol * kcontrol,int event)404 static int tas5720_dac_event(struct snd_soc_dapm_widget *w,
405 struct snd_kcontrol *kcontrol, int event)
406 {
407 struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
408 struct tas5720_data *tas5720 = snd_soc_component_get_drvdata(component);
409 int ret;
410
411 if (event & SND_SOC_DAPM_POST_PMU) {
412 /* Take TAS5720 out of shutdown mode */
413 ret = snd_soc_component_update_bits(component, TAS5720_POWER_CTRL_REG,
414 TAS5720_SDZ, TAS5720_SDZ);
415 if (ret < 0) {
416 dev_err(component->dev, "error waking component: %d\n", ret);
417 return ret;
418 }
419
420 /*
421 * Observe codec shutdown-to-active time. The datasheet only
422 * lists a nominal value however just use-it as-is without
423 * additional padding to minimize the delay introduced in
424 * starting to play audio (actually there is other setup done
425 * by the ASoC framework that will provide additional delays,
426 * so we should always be safe).
427 */
428 msleep(25);
429
430 /* Turn on TAS5720 periodic fault checking/handling */
431 tas5720->last_fault = 0;
432 schedule_delayed_work(&tas5720->fault_check_work,
433 msecs_to_jiffies(TAS5720_FAULT_CHECK_INTERVAL));
434 } else if (event & SND_SOC_DAPM_PRE_PMD) {
435 /* Disable TAS5720 periodic fault checking/handling */
436 cancel_delayed_work_sync(&tas5720->fault_check_work);
437
438 /* Place TAS5720 in shutdown mode to minimize current draw */
439 ret = snd_soc_component_update_bits(component, TAS5720_POWER_CTRL_REG,
440 TAS5720_SDZ, 0);
441 if (ret < 0) {
442 dev_err(component->dev, "error shutting down component: %d\n",
443 ret);
444 return ret;
445 }
446 }
447
448 return 0;
449 }
450
451 #ifdef CONFIG_PM
tas5720_suspend(struct snd_soc_component * component)452 static int tas5720_suspend(struct snd_soc_component *component)
453 {
454 struct tas5720_data *tas5720 = snd_soc_component_get_drvdata(component);
455 int ret;
456
457 regcache_cache_only(tas5720->regmap, true);
458 regcache_mark_dirty(tas5720->regmap);
459
460 ret = regulator_bulk_disable(ARRAY_SIZE(tas5720->supplies),
461 tas5720->supplies);
462 if (ret < 0)
463 dev_err(component->dev, "failed to disable supplies: %d\n", ret);
464
465 return ret;
466 }
467
tas5720_resume(struct snd_soc_component * component)468 static int tas5720_resume(struct snd_soc_component *component)
469 {
470 struct tas5720_data *tas5720 = snd_soc_component_get_drvdata(component);
471 int ret;
472
473 ret = regulator_bulk_enable(ARRAY_SIZE(tas5720->supplies),
474 tas5720->supplies);
475 if (ret < 0) {
476 dev_err(component->dev, "failed to enable supplies: %d\n", ret);
477 return ret;
478 }
479
480 regcache_cache_only(tas5720->regmap, false);
481
482 ret = regcache_sync(tas5720->regmap);
483 if (ret < 0) {
484 dev_err(component->dev, "failed to sync regcache: %d\n", ret);
485 return ret;
486 }
487
488 return 0;
489 }
490 #else
491 #define tas5720_suspend NULL
492 #define tas5720_resume NULL
493 #endif
494
tas5720_is_volatile_reg(struct device * dev,unsigned int reg)495 static bool tas5720_is_volatile_reg(struct device *dev, unsigned int reg)
496 {
497 switch (reg) {
498 case TAS5720_DEVICE_ID_REG:
499 case TAS5720_FAULT_REG:
500 return true;
501 default:
502 return false;
503 }
504 }
505
506 static const struct regmap_config tas5720_regmap_config = {
507 .reg_bits = 8,
508 .val_bits = 8,
509
510 .max_register = TAS5720_MAX_REG,
511 .cache_type = REGCACHE_RBTREE,
512 .volatile_reg = tas5720_is_volatile_reg,
513 };
514
515 static const struct regmap_config tas5720a_q1_regmap_config = {
516 .reg_bits = 8,
517 .val_bits = 8,
518
519 .max_register = TAS5720_MAX_REG,
520 .cache_type = REGCACHE_RBTREE,
521 .volatile_reg = tas5720_is_volatile_reg,
522 };
523
524 static const struct regmap_config tas5722_regmap_config = {
525 .reg_bits = 8,
526 .val_bits = 8,
527
528 .max_register = TAS5722_MAX_REG,
529 .cache_type = REGCACHE_RBTREE,
530 .volatile_reg = tas5720_is_volatile_reg,
531 };
532
533 /*
534 * DAC analog gain. There are four discrete values to select from, ranging
535 * from 19.2 dB to 26.3dB.
536 */
537 static const DECLARE_TLV_DB_RANGE(dac_analog_tlv,
538 0x0, 0x0, TLV_DB_SCALE_ITEM(1920, 0, 0),
539 0x1, 0x1, TLV_DB_SCALE_ITEM(2070, 0, 0),
540 0x2, 0x2, TLV_DB_SCALE_ITEM(2350, 0, 0),
541 0x3, 0x3, TLV_DB_SCALE_ITEM(2630, 0, 0),
542 );
543
544 /*
545 * DAC analog gain for TAS5720A-Q1. There are three discrete values to select from, ranging
546 * from 19.2 dB to 25.0dB.
547 */
548 static const DECLARE_TLV_DB_RANGE(dac_analog_tlv_a_q1,
549 0x0, 0x0, TLV_DB_SCALE_ITEM(1920, 0, 0),
550 0x1, 0x1, TLV_DB_SCALE_ITEM(2260, 0, 0),
551 0x2, 0x2, TLV_DB_SCALE_ITEM(2500, 0, 0),
552 );
553
554 /*
555 * DAC digital volumes. From -103.5 to 24 dB in 0.5 dB or 0.25 dB steps
556 * depending on the device. Note that setting the gain below -100 dB
557 * (register value <0x7) is effectively a MUTE as per device datasheet.
558 *
559 * Note that for the TAS5722 the digital volume controls are actually split
560 * over two registers, so we need custom getters/setters for access.
561 */
562 static DECLARE_TLV_DB_SCALE(tas5720_dac_tlv, -10350, 50, 0);
563 static DECLARE_TLV_DB_SCALE(tas5722_dac_tlv, -10350, 25, 0);
564
tas5722_volume_get(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)565 static int tas5722_volume_get(struct snd_kcontrol *kcontrol,
566 struct snd_ctl_elem_value *ucontrol)
567 {
568 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
569 unsigned int val;
570
571 val = snd_soc_component_read(component, TAS5720_VOLUME_CTRL_REG);
572 ucontrol->value.integer.value[0] = val << 1;
573
574 val = snd_soc_component_read(component, TAS5722_DIGITAL_CTRL2_REG);
575 ucontrol->value.integer.value[0] |= val & TAS5722_VOL_CONTROL_LSB;
576
577 return 0;
578 }
579
tas5722_volume_set(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)580 static int tas5722_volume_set(struct snd_kcontrol *kcontrol,
581 struct snd_ctl_elem_value *ucontrol)
582 {
583 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
584 unsigned int sel = ucontrol->value.integer.value[0];
585
586 snd_soc_component_write(component, TAS5720_VOLUME_CTRL_REG, sel >> 1);
587 snd_soc_component_update_bits(component, TAS5722_DIGITAL_CTRL2_REG,
588 TAS5722_VOL_CONTROL_LSB, sel);
589
590 return 0;
591 }
592
593 static const struct snd_kcontrol_new tas5720_snd_controls[] = {
594 SOC_SINGLE_TLV("Speaker Driver Playback Volume",
595 TAS5720_VOLUME_CTRL_REG, 0, 0xff, 0, tas5720_dac_tlv),
596 SOC_SINGLE_TLV("Speaker Driver Analog Gain", TAS5720_ANALOG_CTRL_REG,
597 TAS5720_ANALOG_GAIN_SHIFT, 3, 0, dac_analog_tlv),
598 };
599
600 static const struct snd_kcontrol_new tas5720a_q1_snd_controls[] = {
601 SOC_DOUBLE_R_TLV("Speaker Driver Playback Volume",
602 TAS5720_Q1_VOLUME_CTRL_LEFT_REG,
603 TAS5720_Q1_VOLUME_CTRL_RIGHT_REG,
604 0, 0xff, 0, tas5720_dac_tlv),
605 SOC_SINGLE_TLV("Speaker Driver Analog Gain", TAS5720_ANALOG_CTRL_REG,
606 TAS5720_ANALOG_GAIN_SHIFT, 3, 0, dac_analog_tlv_a_q1),
607 };
608
609 static const struct snd_kcontrol_new tas5722_snd_controls[] = {
610 SOC_SINGLE_EXT_TLV("Speaker Driver Playback Volume",
611 0, 0, 511, 0,
612 tas5722_volume_get, tas5722_volume_set,
613 tas5722_dac_tlv),
614 SOC_SINGLE_TLV("Speaker Driver Analog Gain", TAS5720_ANALOG_CTRL_REG,
615 TAS5720_ANALOG_GAIN_SHIFT, 3, 0, dac_analog_tlv),
616 };
617
618 static const struct snd_soc_dapm_widget tas5720_dapm_widgets[] = {
619 SND_SOC_DAPM_AIF_IN("DAC IN", "Playback", 0, SND_SOC_NOPM, 0, 0),
620 SND_SOC_DAPM_DAC_E("DAC", NULL, SND_SOC_NOPM, 0, 0, tas5720_dac_event,
621 SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
622 SND_SOC_DAPM_OUTPUT("OUT")
623 };
624
625 static const struct snd_soc_dapm_route tas5720_audio_map[] = {
626 { "DAC", NULL, "DAC IN" },
627 { "OUT", NULL, "DAC" },
628 };
629
630 static const struct snd_soc_component_driver soc_component_dev_tas5720 = {
631 .probe = tas5720_codec_probe,
632 .remove = tas5720_codec_remove,
633 .suspend = tas5720_suspend,
634 .resume = tas5720_resume,
635 .controls = tas5720_snd_controls,
636 .num_controls = ARRAY_SIZE(tas5720_snd_controls),
637 .dapm_widgets = tas5720_dapm_widgets,
638 .num_dapm_widgets = ARRAY_SIZE(tas5720_dapm_widgets),
639 .dapm_routes = tas5720_audio_map,
640 .num_dapm_routes = ARRAY_SIZE(tas5720_audio_map),
641 .idle_bias_on = 1,
642 .use_pmdown_time = 1,
643 .endianness = 1,
644 };
645
646 static const struct snd_soc_component_driver soc_component_dev_tas5720_a_q1 = {
647 .probe = tas5720_codec_probe,
648 .remove = tas5720_codec_remove,
649 .suspend = tas5720_suspend,
650 .resume = tas5720_resume,
651 .controls = tas5720a_q1_snd_controls,
652 .num_controls = ARRAY_SIZE(tas5720a_q1_snd_controls),
653 .dapm_widgets = tas5720_dapm_widgets,
654 .num_dapm_widgets = ARRAY_SIZE(tas5720_dapm_widgets),
655 .dapm_routes = tas5720_audio_map,
656 .num_dapm_routes = ARRAY_SIZE(tas5720_audio_map),
657 .idle_bias_on = 1,
658 .use_pmdown_time = 1,
659 .endianness = 1,
660 };
661
662 static const struct snd_soc_component_driver soc_component_dev_tas5722 = {
663 .probe = tas5720_codec_probe,
664 .remove = tas5720_codec_remove,
665 .suspend = tas5720_suspend,
666 .resume = tas5720_resume,
667 .controls = tas5722_snd_controls,
668 .num_controls = ARRAY_SIZE(tas5722_snd_controls),
669 .dapm_widgets = tas5720_dapm_widgets,
670 .num_dapm_widgets = ARRAY_SIZE(tas5720_dapm_widgets),
671 .dapm_routes = tas5720_audio_map,
672 .num_dapm_routes = ARRAY_SIZE(tas5720_audio_map),
673 .idle_bias_on = 1,
674 .use_pmdown_time = 1,
675 .endianness = 1,
676 };
677
678 /* PCM rates supported by the TAS5720 driver */
679 #define TAS5720_RATES (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 |\
680 SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000)
681
682 /* Formats supported by TAS5720 driver */
683 #define TAS5720_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S18_3LE |\
684 SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_S24_LE)
685
686 static const struct snd_soc_dai_ops tas5720_speaker_dai_ops = {
687 .hw_params = tas5720_hw_params,
688 .set_fmt = tas5720_set_dai_fmt,
689 .set_tdm_slot = tas5720_set_dai_tdm_slot,
690 .mute_stream = tas5720_mute,
691 .no_capture_mute = 1,
692 };
693
694 /*
695 * TAS5720 DAI structure
696 *
697 * Note that were are advertising .playback.channels_max = 2 despite this being
698 * a mono amplifier. The reason for that is that some serial ports such as TI's
699 * McASP module have a minimum number of channels (2) that they can output.
700 * Advertising more channels than we have will allow us to interface with such
701 * a serial port without really any negative side effects as the TAS5720 will
702 * simply ignore any extra channel(s) asides from the one channel that is
703 * configured to be played back.
704 */
705 static struct snd_soc_dai_driver tas5720_dai[] = {
706 {
707 .name = "tas5720-amplifier",
708 .playback = {
709 .stream_name = "Playback",
710 .channels_min = 1,
711 .channels_max = 2,
712 .rates = TAS5720_RATES,
713 .formats = TAS5720_FORMATS,
714 },
715 .ops = &tas5720_speaker_dai_ops,
716 },
717 };
718
719 static const struct i2c_device_id tas5720_id[] = {
720 { "tas5720", TAS5720 },
721 { "tas5720a-q1", TAS5720A_Q1 },
722 { "tas5722", TAS5722 },
723 { }
724 };
725 MODULE_DEVICE_TABLE(i2c, tas5720_id);
726
tas5720_probe(struct i2c_client * client)727 static int tas5720_probe(struct i2c_client *client)
728 {
729 struct device *dev = &client->dev;
730 struct tas5720_data *data;
731 const struct regmap_config *regmap_config;
732 const struct i2c_device_id *id;
733 int ret;
734 int i;
735
736 data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
737 if (!data)
738 return -ENOMEM;
739
740 id = i2c_match_id(tas5720_id, client);
741 data->tas5720_client = client;
742 data->devtype = id->driver_data;
743
744 switch (id->driver_data) {
745 case TAS5720:
746 regmap_config = &tas5720_regmap_config;
747 break;
748 case TAS5720A_Q1:
749 regmap_config = &tas5720a_q1_regmap_config;
750 break;
751 case TAS5722:
752 regmap_config = &tas5722_regmap_config;
753 break;
754 default:
755 dev_err(dev, "unexpected private driver data\n");
756 return -EINVAL;
757 }
758 data->regmap = devm_regmap_init_i2c(client, regmap_config);
759 if (IS_ERR(data->regmap)) {
760 ret = PTR_ERR(data->regmap);
761 dev_err(dev, "failed to allocate register map: %d\n", ret);
762 return ret;
763 }
764
765 for (i = 0; i < ARRAY_SIZE(data->supplies); i++)
766 data->supplies[i].supply = tas5720_supply_names[i];
767
768 ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(data->supplies),
769 data->supplies);
770 if (ret != 0) {
771 dev_err(dev, "failed to request supplies: %d\n", ret);
772 return ret;
773 }
774
775 dev_set_drvdata(dev, data);
776
777 switch (id->driver_data) {
778 case TAS5720:
779 ret = devm_snd_soc_register_component(&client->dev,
780 &soc_component_dev_tas5720,
781 tas5720_dai,
782 ARRAY_SIZE(tas5720_dai));
783 break;
784 case TAS5720A_Q1:
785 ret = devm_snd_soc_register_component(&client->dev,
786 &soc_component_dev_tas5720_a_q1,
787 tas5720_dai,
788 ARRAY_SIZE(tas5720_dai));
789 break;
790 case TAS5722:
791 ret = devm_snd_soc_register_component(&client->dev,
792 &soc_component_dev_tas5722,
793 tas5720_dai,
794 ARRAY_SIZE(tas5720_dai));
795 break;
796 default:
797 dev_err(dev, "unexpected private driver data\n");
798 return -EINVAL;
799 }
800 if (ret < 0) {
801 dev_err(dev, "failed to register component: %d\n", ret);
802 return ret;
803 }
804
805 return 0;
806 }
807
808 #if IS_ENABLED(CONFIG_OF)
809 static const struct of_device_id tas5720_of_match[] = {
810 { .compatible = "ti,tas5720", },
811 { .compatible = "ti,tas5720a-q1", },
812 { .compatible = "ti,tas5722", },
813 { },
814 };
815 MODULE_DEVICE_TABLE(of, tas5720_of_match);
816 #endif
817
818 static struct i2c_driver tas5720_i2c_driver = {
819 .driver = {
820 .name = "tas5720",
821 .of_match_table = of_match_ptr(tas5720_of_match),
822 },
823 .probe_new = tas5720_probe,
824 .id_table = tas5720_id,
825 };
826
827 module_i2c_driver(tas5720_i2c_driver);
828
829 MODULE_AUTHOR("Andreas Dannenberg <dannenberg@ti.com>");
830 MODULE_DESCRIPTION("TAS5720 Audio amplifier driver");
831 MODULE_LICENSE("GPL");
832