1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Configuation settings for the Sentec Cobra Board. 4 * 5 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> 6 */ 7 8 /* --- 9 * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board 10 * Date: 2004-03-29 11 * Author: Florian Schlote 12 * 13 * For a description of configuration options please refer also to the 14 * general u-boot-1.x.x/README file 15 * --- 16 */ 17 18 /* --- 19 * board/config.h - configuration options, board specific 20 * --- 21 */ 22 23 #ifndef _CONFIG_COBRA5272_H 24 #define _CONFIG_COBRA5272_H 25 26 /* --- 27 * Defines processor clock - important for correct timings concerning serial 28 * interface etc. 29 * --- 30 */ 31 32 #define CONFIG_SYS_CLK 66000000 33 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ 34 35 /* Enable Dma Timer */ 36 #define CONFIG_MCFTMR 37 38 /* --- 39 * Define baudrate for UART1 (console output, tftp, ...) 40 * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud 41 * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command 42 * interface 43 * --- 44 */ 45 46 #define CONFIG_MCFUART 47 #define CONFIG_SYS_UART_PORT (0) 48 49 /* --- 50 * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change 51 * timeout acc. to your needs 52 * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000 53 * for 10 sec 54 * --- 55 */ 56 57 #if 0 58 #define CONFIG_WATCHDOG 59 #define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ 60 #endif 61 62 /* --- 63 * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different 64 * bootloader residing in flash ('chainloading'); if you want to use 65 * chainloading or want to compile a u-boot binary that can be loaded into 66 * RAM via BDM set 67 * "#if 0" to "#if 1" 68 * You will need a first stage bootloader then, e. g. colilo or a working BDM 69 * cable (Background Debug Mode) 70 * 71 * Setting #if 0: u-boot will start from flash and relocate itself to RAM 72 * 73 * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE 74 * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000) 75 * 76 * --- 77 */ 78 79 #if 0 80 #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */ 81 #endif 82 83 /* --- 84 * Configuration for environment 85 * Environment is embedded in u-boot in the second sector of the flash 86 * --- 87 */ 88 89 #define LDS_BOARD_TEXT \ 90 . = DEFINED(env_offset) ? env_offset : .; \ 91 env/embedded.o(.text); 92 93 /* 94 * BOOTP options 95 */ 96 #define CONFIG_BOOTP_BOOTFILESIZE 97 98 #ifdef CONFIG_MCFFEC 99 # define CONFIG_MII_INIT 1 100 # define CONFIG_SYS_DISCOVER_PHY 101 # define CONFIG_SYS_RX_ETH_BUFFER 8 102 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 103 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 104 # ifndef CONFIG_SYS_DISCOVER_PHY 105 # define FECDUPLEX FULL 106 # define FECSPEED _100BASET 107 # else 108 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 109 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 110 # endif 111 # endif /* CONFIG_SYS_DISCOVER_PHY */ 112 #endif 113 114 /* 115 *----------------------------------------------------------------------------- 116 * Define user parameters that have to be customized most likely 117 *----------------------------------------------------------------------------- 118 */ 119 120 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/ 121 122 /* The following settings will be contained in the environment block ; if you 123 want to use a neutral environment all those settings can be manually set in 124 u-boot: 'set' command */ 125 126 #if 0 127 128 #define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please 129 enter a valid image address in flash */ 130 131 /* User network settings */ 132 133 #define CONFIG_IPADDR 192.168.100.2 /* default board IP address */ 134 #define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */ 135 136 #endif 137 138 /*---*/ 139 140 /* 141 *----------------------------------------------------------------------------- 142 * End of user parameters to be customized 143 *----------------------------------------------------------------------------- 144 */ 145 146 /* --- 147 * Defines memory range for test 148 * --- 149 */ 150 151 /* --- 152 * Low Level Configuration Settings 153 * (address mappings, register initial values, etc.) 154 * You should know what you are doing if you make changes here. 155 * --- 156 */ 157 158 /* --- 159 * Base register address 160 * --- 161 */ 162 163 #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ 164 165 /* --- 166 * System Conf. Reg. & System Protection Reg. 167 * --- 168 */ 169 170 #define CONFIG_SYS_SCR 0x0003 171 #define CONFIG_SYS_SPR 0xffff 172 173 /* --- 174 * Ethernet settings 175 * --- 176 */ 177 178 #define CONFIG_SYS_DISCOVER_PHY 179 #define CONFIG_SYS_ENET_BD_BASE 0x780000 180 181 /*----------------------------------------------------------------------- 182 * Definitions for initial stack pointer and data area (in internal SRAM) 183 */ 184 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 185 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ 186 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 187 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 188 189 /*----------------------------------------------------------------------- 190 * Start addresses for the final memory configuration 191 * (Set up by the startup code) 192 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 193 */ 194 #define CONFIG_SYS_SDRAM_BASE 0x00000000 195 196 /* 197 *------------------------------------------------------------------------- 198 * RAM SIZE (is defined above) 199 *----------------------------------------------------------------------- 200 */ 201 202 /* #define CONFIG_SYS_SDRAM_SIZE 16 */ 203 204 /* 205 *----------------------------------------------------------------------- 206 */ 207 208 #define CONFIG_SYS_FLASH_BASE 0xffe00000 209 210 #ifdef CONFIG_MONITOR_IS_IN_RAM 211 #define CONFIG_SYS_MONITOR_BASE 0x20000 212 #else 213 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 214 #endif 215 216 #define CONFIG_SYS_MONITOR_LEN 0x20000 217 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 218 219 /* 220 * For booting Linux, the board info and command line data 221 * have to be in the first 8 MB of memory, since this is 222 * the maximum mapped by the Linux kernel during initialization ?? 223 */ 224 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 225 226 /*----------------------------------------------------------------------- 227 * FLASH organization 228 */ 229 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 230 #define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ 231 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */ 232 233 /*----------------------------------------------------------------------- 234 * Cache Configuration 235 */ 236 237 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 238 CONFIG_SYS_INIT_RAM_SIZE - 8) 239 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 240 CONFIG_SYS_INIT_RAM_SIZE - 4) 241 #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) 242 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ 243 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 244 CF_ACR_EN | CF_ACR_SM_ALL) 245 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ 246 CF_CACR_DISD | CF_CACR_INVI | \ 247 CF_CACR_CEIB | CF_CACR_DCM | \ 248 CF_CACR_EUSP) 249 250 /*----------------------------------------------------------------------- 251 * Memory bank definitions 252 * 253 * Please refer also to Motorola Coldfire user manual - Chapter XXX 254 * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf> 255 */ 256 #define CONFIG_SYS_BR0_PRELIM 0xFFE00201 257 #define CONFIG_SYS_OR0_PRELIM 0xFFE00014 258 259 #define CONFIG_SYS_BR1_PRELIM 0 260 #define CONFIG_SYS_OR1_PRELIM 0 261 262 #define CONFIG_SYS_BR2_PRELIM 0 263 #define CONFIG_SYS_OR2_PRELIM 0 264 265 #define CONFIG_SYS_BR3_PRELIM 0 266 #define CONFIG_SYS_OR3_PRELIM 0 267 268 #define CONFIG_SYS_BR4_PRELIM 0 269 #define CONFIG_SYS_OR4_PRELIM 0 270 271 #define CONFIG_SYS_BR5_PRELIM 0 272 #define CONFIG_SYS_OR5_PRELIM 0 273 274 #define CONFIG_SYS_BR6_PRELIM 0 275 #define CONFIG_SYS_OR6_PRELIM 0 276 277 #define CONFIG_SYS_BR7_PRELIM 0x00000701 278 #define CONFIG_SYS_OR7_PRELIM 0xFF00007C 279 280 /*----------------------------------------------------------------------- 281 * LED config 282 */ 283 #define LED_STAT_0 0xffff /*all LEDs off*/ 284 #define LED_STAT_1 0xfffe 285 #define LED_STAT_2 0xfffd 286 #define LED_STAT_3 0xfffb 287 #define LED_STAT_4 0xfff7 288 #define LED_STAT_5 0xffef 289 #define LED_STAT_6 0xffdf 290 #define LED_STAT_7 0xff00 /*all LEDs on*/ 291 292 /*----------------------------------------------------------------------- 293 * Port configuration (GPIO) 294 */ 295 #define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external 296 GPIO*/ 297 #define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs 298 (1^=output, 0^=input) */ 299 #define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ 300 #define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART 301 configuration */ 302 #define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ 303 #define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */ 304 #define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */ 305 306 #endif /* _CONFIG_COBRA5272_H */ 307