Lines Matching refs:console
14 the console before standard serial driver is probed. The console is
33 bool "Support for console on AMBA serial port"
38 console (the system console is the device which receives all kernel
41 Even if you say Y here, the currently visible framebuffer console
42 (/dev/tty0) will still be used as the system console by default, but
44 "console=ttyAM0". (Try "man bootparam" or see the documentation of
60 bool "Support for console on AMBA serial port"
66 console (the system console is the device which receives all kernel
69 Even if you say Y here, the currently visible framebuffer console
70 (/dev/tty0) will still be used as the system console by default, but
72 "console=ttyAMA0". (Try "man bootparam" or see the documentation of
77 bool "Early console using ARM semihosting"
83 Support for early debug console using ARM semihosting. This enables
84 the console before standard serial driver is probed. This is enabled
85 with "earlycon=smh" on the kernel command line. The console is
89 bool "Early console using RISC-V SBI"
95 Support for early debug console using RISC-V SBI. This enables
96 the console before standard serial driver is probed. This is enabled
97 with "earlycon=sbi" on the kernel command line. The console is
116 bool "Support for console on a BCM1xxx DUART serial port"
122 system console (the system console is the device which receives all
139 bool "Support for console on AT91 serial port"
144 AT91 processor as the system console (the system
145 console is the device which receives all kernel messages and
176 /dev/, and pass "console=ttyATn" to the kernel.
181 bool "Serial console over KGDB NMI debugger port"
185 as a normal console (assuming that the port is attached to KGDB).
189 This is because this console driver processes the input in NMI
192 Note that since the console interprets input and uses polling
195 use raw console.
208 bool "Support for console on meson"
214 system console (the system console is the device which
228 bool "Support for console on CLPS711X serial port"
232 Even if you say Y here, the currently visible virtual console
233 (/dev/tty0) will still be used as the system console by default, but
235 "console=ttyCL1".
265 bool "Support for console on Samsung SoC serial port"
271 an virtual console.
273 Even if you say Y here, the currently visible virtual console
274 (/dev/tty0) will still be used as the system console by default, but
276 "console=ttySACx". (Try "man bootparam" or see the documentation of
302 bool "Support for console on a Tegra TCU serial port"
308 system console (the system console is the device which receives all
344 bool "Support console on DECstation DZ serial driver"
350 system console (the system console is the device which receives all
354 Note that the firmware uses ttyS3 as the serial console on
374 bool "Support for console on a DECstation Z85C30 serial port"
380 system console (the system console is the device which receives all
384 Note that the firmware uses ttyS1 as the serial console on the
404 make it the console by answering Y to this option.
406 Even if you say Y here, the currently visible virtual console
407 (/dev/tty0) will still be used as the system console by default, but
409 "console=ttyFB". (Try "man bootparam" or see the documentation of
437 CPU you can make it the console by answering Y to this option.
439 Even if you say Y here, the currently visible virtual console
440 (/dev/tty0) will still be used as the system console by default, but
442 "console=ttySA0". (Try "man bootparam" or see the documentation of
466 CPU you can make it the console by answering Y to this option.
468 Even if you say Y here, the currently visible virtual console
469 (/dev/tty0) will still be used as the system console by default, but
471 "console=ttySA0". (Try "man bootparam" or see the documentation of
491 CPU you can make it the console by answering Y/M to this option.
493 Even if you say Y/M here, the currently visible virtual console
494 (/dev/tty0) will still be used as the system console by default, but
496 "console=ttymxc0". (Try "man bootparam" or see the documentation of
522 bool "Support for console on Xilinx uartlite serial port"
528 console (the system console is the device which receives all kernel
559 on your Sparc system as the console, you can do so by answering
575 on your Sparc system as the console, you can do so by answering
588 software console. The following steps need to be completed to use
594 root on this console.)
595 4. Change the kernel command console parameter to: console=ttyB0
598 bool "Support for console on serial MUX"
604 bool "PDC software console support"
607 Saying Y here will enable the software based PDC console to be
608 used as the system console. This is useful for machines in
609 which the hardware based console has not been written yet. The
610 following steps must be completed to use the PDC console:
615 root on this console.)
616 4. Change the kernel command console parameter to: console=ttyB0
631 on your Sparc system as the console, you can do so by answering
638 This driver supports the console device found on SUN4V Sparc
671 bool "Support for console on SuperH SCI(F)" if EXPERT
677 bool "Support for early console on SuperH SCI(F)" if EXPERT
700 bool "Enable LPC32XX high speed UART serial console"
705 ports on the LPC32XX as the console, you can do so by answering
734 bool "Coldfire serial console support"
738 Enable a ColdFire internal serial port to be the system console.
780 on your (Power)Mac as the console, you can do so by answering
792 bool "Support for console on CPM SCC/SMC serial port"
797 console (the system console is the device which receives all kernel
800 Even if you say Y here, the currently visible framebuffer console
801 (/dev/tty0) will still be used as the system console by default, but
803 "console=ttyCPM0". (Try "man bootparam" or see the documentation of
815 to use a serial port as a console, this must be included in kernel and
819 bool "PIC32 serial console support"
823 If you have a PIC32, this driver supports the putting a console on one
826 Say Y to use the PIC32 console, otherwise say N.
835 for use as console, it must be included in kernel and not as a
844 of the Freescale MPC52xx family as a console.
851 Select the MPC52xx console baud rate.
853 console baudrate
902 bool "Enable NEC VR4100 series Serial Interface Unit console"
907 a console on a serial port, say Y. Otherwise, say N.
931 bool "MSM serial console support"
948 Serial console driver for Qualcomm Technologies Inc's GENI based
957 bool "VIA VT8500 serial console support"
979 console.
981 Even if you say Y here, the currently visible virtual console
982 (/dev/tty0) will still be used as the system console by default, but
984 "console=ttyOx". (Try "man bootparam" or see the documentation of
1004 system console.
1006 Even if you say Y here, the currently visible virtual console
1007 (/dev/tty0) will still be used as the system console by default, but
1009 "console=ttySIFx". (Try "man bootparam" or see the documentation of
1029 system console.
1053 Support for console on SCCNXP serial ports.
1110 BCM7xxx (STB) - DOCSIS console
1119 you can make it the console by answering Y to this option.
1133 Support for running a console on the GRLIB APBUART
1142 bool "Altera JTAG UART console support"
1147 Enable a Altera JTAG UART port to be the system console.
1154 Bypass console output and keep going even if there is no
1182 bool "Altera UART console support"
1187 Enable a Altera UART port to be the system console.
1206 bool "Support for console on Intel EG20T PCH UART/OKI SEMICONDUCTOR ML7213 IOH"
1210 Say Y here if you wish to use the PCH UART as the system console
1211 (the system console is the device which receives all kernel messages and
1224 bool "MXS AUART console support"
1228 Enable a MXS AUART port to be the system console.
1239 bool "Cadence UART console support"
1244 Enable a Cadence UART port to be the system console.
1263 Enable a built-in UART port of the AR933X to be the system console.
1274 bool "MPS2 UART console support"
1348 you can make it the console by answering Y to this option.
1364 SoCs, you can make it the console by answering Y to this option.
1379 SoCs, you can make it the console by answering Y to this option.
1394 bool "Support for console on ST ASC"
1417 bool "Spreadtrum UART console support"
1422 Support for early debug console using Spreadtrum's serial. This enables
1423 the console before standard serial driver is probed. This is enabled
1424 with "earlycon" on the kernel command line. The console is
1441 bool "Support for console on STM32"
1463 Say 'Y' here if you wish to use Armada-3700 UART as the system console.
1464 (the system console is the device which receives all kernel messages
1485 as the system console.
1504 console. Only earlycon is implemented currently.
1521 bool "Support for console on MILBEAUT USIO/UART serial port"
1528 SoCs as the system console (the system console is the device which
1554 bool "LiteUART serial port console support"
1560 controller from LiteX SoC builder as the system console
1561 (the system console is the device which receives all kernel messages