Searched refs:AUI (Results 1 – 13 of 13) sorted by relevance
| /linux/Documentation/networking/device_drivers/ethernet/dec/ |
| A D | de4x5.rst | 12 - DE435 TP/COAX/AUI PCI
13 - DE450 TP/COAX/AUI PCI
173 TP, TP_NW, BNC, AUI, BNC_AUI, 100Mb, 10Mb, AUTO
183 DE4X5_OPTS = -DDE4X5_PARM='"eth0:fdx autosense=AUI eth2:autosense=TP"'
185 Yes, I know full duplex isn't permissible on BNC or AUI; they're just
|
| /linux/Documentation/networking/device_drivers/ethernet/ti/ |
| A D | tlan.rst | 75 the adapter to use the AUI interface instead of the 10 Base T
78 device that does not have an AUI/BNC connector will probably
|
| /linux/Documentation/networking/device_drivers/ethernet/smsc/ |
| A D | smc9.rst | 38 2 for AUI ( or BNC on some cards )
|
| /linux/drivers/net/ethernet/dec/tulip/ |
| A D | de4x5.c | 2427 case AUI: in dc21040_autoconf()
2564 } else if (lp->autosense == AUI) { in dc21041_autoconf()
2565 lp->media = AUI; in dc21041_autoconf()
2587 lp->media = AUI; in dc21041_autoconf()
2653 case AUI: in dc21041_autoconf()
2886 case AUI: in dc21140m_autoconf()
2968 lp->media = AUI; in dc2114x_autoconf()
3032 case AUI: in dc2114x_autoconf()
3224 lp->media = AUI; in srom_map_media()
5216 lp->params.autosense = AUI; in de4x5_parse_params()
[all …]
|
| A D | de4x5.h | 818 #define AUI 0x0008 /* Thickwire */ macro
|
| /linux/Documentation/networking/device_drivers/ethernet/3com/ |
| A D | 3c509.rst | 77 connector), not its AUI (thick-net) or 10base2 (thin-net/coax) interfaces.
78 AUI and 10base2 network cabling is physically incapable of full-duplex
114 1 AUI (thick-net / DB15 connector)
|
| A D | vortex.rst | 109 1 10Mbs AUI
255 10base2 and AUI interfaces.
257 Prior to January, 2001 this driver would autoeselect the 10base2 or AUI
|
| /linux/drivers/net/ethernet/apple/ |
| A D | Kconfig | 37 MACE ethernet chip have an Apple AUI port (small 15-pin connector),
|
| /linux/net/ethtool/ |
| A D | common.c | 119 __DEFINE_SPECIAL_MODE_NAME(AUI, "AUI"),
263 __DEFINE_SPECIAL_MODE_PARAMS(AUI),
|
| /linux/include/uapi/linux/ |
| A D | ethtool.h | 1712 #define SUPPORTED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI)
1752 #define ADVERTISED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI)
|
| /linux/Documentation/networking/device_drivers/ethernet/cirrus/ |
| A D | cs89x0.rst | 70 10BaseT-only or 3-media configurations (10BaseT, 10Base2, and AUI for 10Base-5
118 * Appropriate cable (and connector for AUI, 10BASE-2) for your network
229 address of 200h, interrupt 10, and use the AUI media connection. The following
510 a 10Base-2 or AUI connection.)
|
| /linux/drivers/net/ethernet/mellanox/mlx5/core/ |
| A D | en_ethtool.c | 812 supported, AUI); in ptys2ethtool_supported_advertised_port()
814 advertising, AUI); in ptys2ethtool_supported_advertised_port()
|
| /linux/drivers/net/phy/ |
| A D | phylink.c | 127 phylink_set(mask, AUI); in phylink_set_port_modes()
|
Completed in 45 milliseconds