| /linux/Documentation/block/ |
| A D | null_blk.rst | 30 queue_mode=[0-2]: Default: 2-Multi-queue
42 gb=[Size in GB]: Default: 250GB
52 irqmode=[0-2]: Default: 1-Soft-irq
67 submit_queues=[1..nr_cpus]: Default: 1
78 use_per_node_hctx=[0/1]: Default: 0
88 no_sched=[0/1]: Default: 0
96 blocking=[0/1]: Default: 0
106 shared_tags=[0/1]: Default: 0
115 zoned=[0/1]: Default: 0
124 zone_size=[MB]: Default: 256
[all …]
|
| /linux/Documentation/networking/ |
| A D | ip-sysctl.rst | 50 Default: FALSE
78 Default: 0
163 Default: 128
170 Default: 512
268 Default: 64
314 Default: 1
388 Default: 3
407 Default: 2
452 Default: 0
631 Default: 3
[all …]
|
| A D | mptcp-sysctl.rst | 16 Default: 1 (enabled)
26 Default: 120
34 Default: 0
47 Default: 1
59 Default: 4
|
| /linux/Documentation/devicetree/bindings/devfreq/ |
| A D | rk3399_dmc.txt | 81 the DRAM side driver strength in ohms. Default
91 Default value is 40.
95 driver strength. Default value is 40.
107 the DRAM side driver strength in ohms. Default
117 Default value is 40.
121 driver strength. Default value is 40.
138 Default value is 40.
142 Default value is 40.
146 line) driver strength. Default value is 40.
150 strength. Default value is 80.
[all …]
|
| /linux/Documentation/devicetree/bindings/phy/ |
| A D | apm-xgene-phy.txt | 15 Default is "ok".
21 127 in unit of one bit period. Default is 10.
26 supported link speed on the host. Default is 0.
30 between 0 to 31 in unit of dB. Default is 3.
34 Default is 199500 uV.
38 uV. Default is 0.
42 Default is 0x0.
45 between 0 to 0x1f in unit of 18.2mV. Default is 0xf.
|
| A D | mxs-usb-phy.txt | 19 that terminates the DN output signal. Default: 45
22 that terminates the DP output signal. Default: 45
24 the 17.78mA TX reference current. Default: 100
|
| /linux/Documentation/devicetree/bindings/sound/ |
| A D | max9892x.txt | 15 MAX98925/MAX98926 slot range : 0 ~ 30, Default : 0
16 MAX98927 slot range : 0 ~ 15, Default : 0
19 MAX98925/MAX98926 slot range : 0 ~ 30, Default : 0
20 MAX98927 slot range : 0 ~ 15, Default : 0
29 Range : 0 (off), 1 (on), Default : 0
|
| A D | cs35l32.txt | 24 2 = (Default) Boost voltage fixed in Bypass Mode (VBST = VP).
31 2 = (Default) left/right channels VMON[15:0], IMON [15:0].
36 0 = (Default) One IC.
42 2 = 3.3V (Default)
49 3 = 3.4V (Default)
|
| A D | max98373.txt | 16 slot range : 0 ~ 15, Default : 0
19 slot range : 0 ~ 15, Default : 0
22 slot range : 0 ~ 15, Default : 0
29 Boolean, define to enable the interleave mode, Default : false
|
| A D | wlf,wm8962.yaml | 61 Default register value for R48 (Additional Control 4).
113 0x0000 /* 0:Default */
114 0x0000 /* 1:Default */
116 0x0000 /* 3:Default */
118 0x0000 /* 5:Default */
|
| A D | cs42l42.txt | 25 0 = (Default) Shorted to tip when unplugged, open when plugged.
39 5 - (Default) 1s,
51 5 - (Default) 1s,
61 Default = 100ms
69 Default = 10ms
83 Default = < 15 8 4 1>
|
| A D | cs35l36.txt | 16 (Default) VP
22 (Default) 4.50 Amps
28 1000 = 1uH (Default)
40 0x01 - Class H Tracking (Default)
68 4 = 100ms (Default)
85 2 = 125C (Default)
92 1 = Push-pull (Default)
97 0 = PDM_DATA / SWIRE_SD / INT (Default)
|
| /linux/Documentation/devicetree/bindings/media/i2c/ |
| A D | tvp7002.txt | 10 - hsync-active: HSYNC Polarity configuration for the bus. Default value when
13 - vsync-active: VSYNC Polarity configuration for the bus. Default value when
16 - pclk-sample: Clock polarity of the bus. Default value when this property is
21 0 = Normal Operation (Active Low, Default)
27 0 = Normal Operation (Active Low, Default)
|
| /linux/Documentation/virt/ |
| A D | guest-halt-polling.rst | 38 Default: 200000
45 Default: 2
53 Default: 2
65 Default: 50000
73 Default: Y
|
| /linux/Documentation/devicetree/bindings/clock/ |
| A D | xgene.txt | 50 Default is 0.
51 - csr-mask : CSR reset mask bit. Default is 0xF.
53 Default is 0x8.
54 - enable-mask : CSR enable mask bit. Default is 0xF.
56 Default is 0x0.
57 - divider-width : Width of the divider register. Default is 0.
58 - divider-shift : Bit shift of the divider register. Default is 0.
|
| /linux/Documentation/devicetree/bindings/power/supply/ |
| A D | maxim,max17042.yaml | 42 Default is not to report cold events.
48 Default is not to report over heating events.
54 Default is not to report dead battery events.
60 Default is not to report over-voltage events.
|
| /linux/Documentation/ABI/testing/ |
| A D | sysfs-bus-iio-chemical-sgp40 | 8 Default value: 25000 (25 °C)
17 Default value: 50000 (50 % relative humidity)
31 Default value: 30000
|
| /linux/Documentation/devicetree/bindings/iio/frequency/ |
| A D | adi,adf4350.yaml | 61 description: Enables positive phase detector polarity. Default negative.
65 description: Enables 6ns lock detect precision. Default = 10ns.
70 Enables lock detect for integer-N mode. Default = factional-N mode.
74 description: Charge pump current in mA. Default = 2500mA.
93 description: Enables low spur mode. Default = Low noise mode.
135 Default = Output of RF dividers.
|
| /linux/Documentation/devicetree/bindings/memory-controllers/ |
| A D | atmel,ebi.txt | 49 Default to 8 when undefined.
52 Default to "select" when undefined.
55 Default to "ncs" when undefined.
58 Default to "ncs" when undefined.
61 Default to "disabled" when undefined.
72 Default to "normal" when undefined.
|
| /linux/Documentation/devicetree/bindings/mtd/ |
| A D | orion-nand.txt | 9 - cle : Address line number connected to CLE. Default is 0
10 - ale : Address line number connected to ALE. Default is 1
11 - bank-width : Width in bytes of the device. Default is 1
|
| /linux/Documentation/arm64/ |
| A D | legacy_instructions.rst | 18 Generates undefined instruction abort. Default for instructions that
51 :Default: Undef (0)
57 :Default: Emulate (1)
63 :Default: Emulate (1)*
|
| /linux/tools/perf/Documentation/ |
| A D | perf-config.txt | 94 # Default, disable using /dev/null
191 Default values are 'green' and 'default'.
199 Default values are 'black' and 'lightgray'.
203 Default values are 'blue', 'default'.
206 Default values are 'magenta', 'default'.
209 Default values are 'white', 'blue'.
318 Default is 'false'.
338 Default is 'false'.
354 Default is 'false'.
369 Default is 'false'.
[all …]
|
| /linux/Documentation/scsi/ |
| A D | dc395x.rst | 32 Default: 0, Acceptable values: 0 or 1
40 Default: 7, Acceptable values: 0 to 15
45 Default: 1, Acceptable value: 0 to 7
91 Default: 3, Acceptable values: 0-5
96 Default: 1, Acceptable values: 0-180
|
| /linux/Documentation/fb/ |
| A D | matroxfb.rst | 127 it always probe for memory. Default is to use whole detected
206 Default is `every` known device.
239 or panel. Default value is now read back from hardware - so you
246 Default setting is 100 for cards below G400 or G400 without DFP,
251 above for detailed explanation. Default is 640x480x8bpp if driver
266 pixel line of picture. Default is derived from `vesa` option.
268 pulse. Default is derived from `vesa` option.
272 Default is derived from `vesa` option.
274 pulse. Default is derived from `vesa` option.
284 Default depends on `vesa`.
[all …]
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| A D | max77693.txt | 54 Default: 4200000
58 Default: 3600000
64 Default: 100
69 Default: 3500000
76 Default: 4300000
100 Default: 3300
105 Default: 2400
|