Searched refs:operate (Results 1 – 25 of 196) sorted by relevance
12345678
| /linux/Documentation/mips/ |
| A D | ingenic-tcu.rst | 29 operate.
35 - On the oldest SoCs (up to JZ4740), all of the eight channels operate in
37 - On JZ4725B, channel 5 operates as TCU2, the others operate as TCU1.
38 - On newest SoCs (JZ4750 and above), channels 1-2 operate as TCU2, the
39 others operate as TCU1.
|
| /linux/Documentation/devicetree/bindings/phy/ |
| A D | microchip,sparx5-serdes.yaml | 31 The SERDES6G is a high-speed SERDES interface, which can operate at
41 The SERDES10G is a high-speed SERDES interface, which can operate at
54 The SERDES25G is a high-speed SERDES interface, which can operate at
|
| /linux/Documentation/devicetree/bindings/power/supply/ |
| A D | qcom,pm8941-charger.yaml | 52 Battery voltage limit in uV above which fast charging may operate; Defaults to 3.2V
53 Below this value linear or switch-mode auto-trickle-charging will operate.
60 Battery voltage limit in uV below which fast charging may operate; Defaults to 4.2V
96 Input voltage level in uV above which charging may operate. Defaults to 4.3V.
|
| A D | battery.yaml | 102 - description: minimum temperature at which battery can operate
103 - description: maximum temperature at which battery can operate
|
| /linux/Documentation/devicetree/bindings/serial/ |
| A D | nxp,sc16is7xx.txt | 25 should operate in IrDA mode.
61 should operate in IrDA mode.
|
| /linux/Documentation/scsi/ |
| A D | bnx2fc.rst | 13 depend on the state of the network interfaces to operate. As such, the network
28 2. Configure the interfaces on which bnx2fc driver has to operate on.
|
| /linux/Documentation/devicetree/bindings/mtd/ |
| A D | microchip,mchp23k256.txt | 8 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
|
| /linux/Documentation/sh/ |
| A D | booting.rst | 9 inter-operate with old bootloaders must either use a builtin DTB or
|
| /linux/Documentation/devicetree/bindings/ipmi/ |
| A D | aspeed,ast2400-ibt-bmc.txt | 18 interrupt, the driver will operate in poll mode.
|
| /linux/drivers/usb/dwc2/ |
| A D | Kconfig | 35 driver to operate in Host-only mode.
45 driver to operate in Peripheral-only mode. This option requires
|
| /linux/drivers/pci/endpoint/ |
| A D | Kconfig | 14 controller that can operate in endpoint mode.
|
| /linux/Documentation/driver-api/ |
| A D | mailbox.rst | 43 The client might want to operate in blocking mode (synchronously
106 dc_sync->cl.tx_done = NULL; /* operate in blocking mode */
|
| /linux/Documentation/devicetree/bindings/timer/ |
| A D | ti,keystone-timer.txt | 6 timers, each half can operate in conjunction (chain mode) or independently
|
| A D | renesas,ostm.yaml | 15 can operate in either interval count down timer or free-running compare match
|
| A D | ti,davinci-timer.txt | 6 timers, each half can operate in conjunction (chain mode) or independently
|
| /linux/Documentation/devicetree/bindings/net/can/ |
| A D | tcan4x5x.txt | 12 operate at should be less than or equal to 18 MHz.
|
| /linux/fs/sysfs/ |
| A D | Kconfig | 16 Some system agents rely on the information in sysfs to operate.
|
| /linux/tools/io_uring/ |
| A D | README | 17 io_uring-bench should operate on. This uses the raw io_uring
|
| /linux/Documentation/devicetree/bindings/iio/temperature/ |
| A D | melexis,mlx90632.yaml | 20 operate and measure ambient temperature in range of -20 to 85 degrees
|
| /linux/Documentation/devicetree/bindings/media/ |
| A D | samsung-s5k6a3.txt | 23 configured to operate, in Hz; if this property is not
|
| A D | samsung-s5k5baf.txt | 23 configured to operate, in Hz; if this property is not
|
| /linux/Documentation/devicetree/bindings/cpufreq/ |
| A D | cpufreq-st.txt | 7 the DT and operate in the usual way.
|
| /linux/Documentation/i2c/busses/ |
| A D | i2c-taos-evm.rst | 47 to operate at 1200 bps. However, I don't think this is a big concern in
|
| /linux/Documentation/power/ |
| A D | opp.rst | 70 As the system proceeds to operate, SoC framework may choose to make certain
77 operational functions operate only on available opps:
152 /* dont operate on the pointer.. just do a sanity check.. */
347 for the OPP library to operate on. Pointer to this structure is
|
| /linux/Documentation/devicetree/bindings/net/ |
| A D | micrel.txt | 39 - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
|
Completed in 23 milliseconds
12345678