Searched refs:shut (Results 1 – 25 of 87) sorted by relevance
1234
| /linux/Documentation/devicetree/bindings/power/reset/ |
| A D | ltc2952-poweroff.txt | 3 This chip is used to externally trigger a system shut down. Once the trigger has
4 been sent, the chip's watchdog has to be reset to gracefully shut down.
21 assertion before executing shut down procedure.
|
| /linux/Documentation/ABI/stable/ |
| A D | sysfs-driver-firmware-zynqmp | 71 shut down. This may result in the FPD power
72 domain being shut down provided that no other
75 The complete PS will be shut down, including the
79 The complete system/device is shut down.
|
| /linux/Documentation/hwmon/ |
| A D | tmp108.rst | 35 the TMP108 has a one-shot mode where the device is normally shut-down. When a
37 and then the device is shut down automatically. (This driver only supports
|
| /linux/drivers/accessibility/speakup/ |
| A D | kobjects.c | 338 char shut; in silent_store() local
353 shut = 1; in silent_store()
356 shut = 0; in silent_store()
359 shut |= 0x40; in silent_store()
361 spk_shut_up |= shut; in silent_store()
363 spk_shut_up &= ~shut; in silent_store()
|
| /linux/Documentation/devicetree/bindings/sound/ |
| A D | ti,tas6424.txt | 9 - standby-gpios: GPIO used to shut the TAS6424 down.
|
| A D | realtek,rt1015p.yaml | 25 0 means shut down; 1 means power on.
|
| A D | tas2562.yaml | 38 shut-down-gpios:
|
| /linux/Documentation/devicetree/bindings/clock/ |
| A D | idt,versaclock5.yaml | 86 shut down if the SD/OE pin is driven high. If 0, this disables the
87 shutdown functionality: the chip will never be shut down based on
|
| /linux/Documentation/power/ |
| A D | tricks.rst | 19 * use vga text console, shut down X. [If you really want X, you might
|
| /linux/Documentation/networking/ |
| A D | alias.rst | 49 If the base device is shut down the added aliases will be deleted too.
|
| A D | multiqueue.rst | 25 comes online or when it's completely shut down (unregister_netdev(), etc.).
|
| /linux/Documentation/devicetree/bindings/iio/frequency/ |
| A D | adf4371.yaml | 40 output stage will shut down until the ADF4371/ADF4372 achieves lock as
|
| /linux/drivers/md/ |
| A D | dm-snap.c | 1053 goto shut; in snapshot_merge_next_chunks()
1060 goto shut; in snapshot_merge_next_chunks()
1073 goto shut; in snapshot_merge_next_chunks()
1124 shut: in snapshot_merge_next_chunks()
1151 goto shut; in merge_callback()
1156 goto shut; in merge_callback()
1162 goto shut; in merge_callback()
1166 goto shut; in merge_callback()
1172 shut: in merge_callback()
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| A D | twl4030-power.txt | 21 configuration is used with the external oscillator being shut
|
| /linux/Documentation/admin-guide/nfs/ |
| A D | nfsd-admin-interfaces.rst | 25 On startup, nfsd and lockd grace periods start. nfsd is shut down by a write of
|
| /linux/Documentation/ABI/testing/ |
| A D | sysfs-bus-papr-pmem | 20 shut-down event.
|
| A D | sysfs-class-chromeos-driver-cros-ec-lightbar | 57 power on, shut down, or while running. Reading from this
|
| /linux/Documentation/crypto/ |
| A D | crypto_engine.rst | 32 Start it via ``crypto_engine_start()``. When finished with your work, shut down the
|
| /linux/arch/sh/ |
| A D | Kconfig.debug | 11 on-board Ethernet interface, and shut down the hardware). Note this
|
| /linux/Documentation/devicetree/bindings/gpio/ |
| A D | gpio-eic-sprd.txt | 14 reliability. In addition, this sub-module's clock can be shut off
|
| /linux/Documentation/devicetree/bindings/remoteproc/ |
| A D | qcom,hexagon-v56.txt | 87 shut down
|
| A D | st,stm32-rproc.yaml | 64 is about to be shut down.
|
| A D | qcom,wcnss-pil.txt | 66 it should shut down
|
| /linux/Documentation/process/ |
| A D | kernel-driver-statement.rst | 15 model and shut their users off from the expertise of the Linux
|
| /linux/Documentation/admin-guide/media/ |
| A D | philips.rst | 88 When power_save is enabled (set to 1), the module will try to shut down
92 will shut down, but never wake up). Consider this experimental. By
|
Completed in 873 milliseconds
1234